Equitel E411 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 49

Equitel E411 Скачать руководство пользователя страница 18

June 2015 - Ed.2.1

Audio over IP decoders E411, E413, E415 & E417 technical manual

Page 14

Chapter 4: Configuration and control of the device

The devices have an integrated Web server that allows you to configure and control them remotely from any
Web browser.

This document will focus on the Web server for the E417 model, indicating in each case the features that are
not available in other models.

4.1

Accessing the device

Connect the device to the Ethernet network and the power supply

7

.

The devices are configured in factory to acquire its IP address by DHCP. If your network has a DCHP server, it
will assign a valid IP to the device about 40 seconds after powering the device.

If there is no DHCP server or isn't accessible for any reason, after 3 minutes approximately, the device will
configure itself with the following access parameters:

IP:

192.168.1.1

Subnet Mask:

255.255.255.0

Gateway:

192.168.1.254

There are three methods to know the IP address of the device:



Connect headphones to the connector

and momentarily press the "IP/RD" button

. The

device will say its IP address through the headphones.



Using the free "EQUITEL Devices Searcher" application

8

, for locating Equitel devices in an Ethernet

network.



Using the free application "ENALite"

8

to access to the device.

Once the IP is known, you can access the web server with a standard web browser following this steps:



Configure the computer's IP in the same subnet as the device and make sure there are no other
devices on the network with the same IP addresses.



Start your browser and type the IP address of the device in the access bar.



A dialog box requesting an username and password will appear. Devices are shipped with the
following credentials by default:

User:

admin

Password

admin

7

In PoE models, you can connect the device directly to a PoE switch.

8

You can download the applications from our website:

www.ena.equitel.es

10

6

«
...
16
17
18
19
20
...
»

Содержание E411


















































Отзывы:

Нет отзывов