background image

Epygi Technologies    

 

 

                                                  Configuring Quadro with ISDN

 

 

Fig. 7: ISDN Wizard – Page 3 

ISDN L3 Timers:  

 

The  T302 Timer text field requires the value for the T302 timer in milliseconds 

(digit values from 0 to 15000) and indicates the time frame system is waiting for 
digit to be dialed and when timer expires, it initiates the call.  

 

The  T309 Timer text field requires the value for the T309 timer in milliseconds 

(digit values from 0 to 90000) responsible for call steadiness during link 
disconnection within the period equal to this timer value. If the value in this field is 

0, T309 timer will be disabled.  

 

The  T310 Timer text field requires the value for the T310 timer in milliseconds 

(digit values from 1000 to 120000) responsible for the outgoing call steadiness 
when CALL PROCEEDING is already received from the destination but call 

confirmation (ALERT, CONNECT, DISC or PROGRESS) is not yet arrived.  

 

The  Alert Guard Timeout requires the value for the Alert Guard Timer in 

milliseconds (numeric values from 0 to 500) between CALL PROC and ALERT 

messages. Timer it is used when Quadro is connected to a slow ISDN-PBX. 
Recommended values are: 

- fast connection (0ms); 

- normal connection  (150ms), default; 
- slow connection  ISDN-PBX (350ms); 
- very slow connection  ISDN-PBX (500ms).  

9.

 

Following fields need to be inserted according to the ISP requirement: 

 

The Switch

 Type is another configuration parameter that depends on the Service 

 

election CO should feedback only by the timeslot used for the call 

request.  

Provider.  
The Channel Selection drop down list is used to select between the Preferred and 

Exclusive B channel selection methods. For Preferred channel selection, the CO 

answers to the call request by the first available timeslot, while for Exclusive 
channel s

 

                PAGE 7  

                          7-Feb-06 

Содержание Quadro Quadro 16xi

















Отзывы: