Epson SC-F9300 series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 146

background image

When performing

500mm Pattern

: Approximately

970 mm

Setting procedure

A

Check that the printer is ready, and load the
media according to the actual usage conditions.

When using the Auto Take-up Reel Unit,
attach the media to the roll core.

U

“Loading media” on page 27

U

“Using the Auto Take-up Reel Unit” on

B

Press the

Menu

button.

The settings menu will be displayed.

C

Select

Media Setup

-

Customize Settings

-

Media Adjust

-

Manual

-

Feed Adjustment

.

D

Press the

d

/

u

buttons and select the Feed

Adjustment to execute.

E

Press the

Z

button to print the adjustment

pattern.

Wait until printing is complete.

F

Check the printed adjustment pattern.

When Standard is selected

Two groups of adjustment patterns, A and B,
are printed. Select the pattern with the least
amount of overlapping or gaps for each group.
Select “0.0” in the cases shown below.

If there are patterns where the overlapping or
gaps are the same, enter the middle value in
step 7. Enter “-0.05%” in the cases shown below.

If all of the adjustment patterns contain either
overlapping or misalignments, and you cannot
narrow it down to one, enter “0.0%”, for the
time being.

In this situation, the media feed is not adjusted.
Do the following steps to complete Feed
Adjustment, and then execute Feed Adjustment
-

500mm Pattern

.

When 100mm Pattern, 250mm Pattern, or
500mm Pattern is selected

Measure using a scale of up to 0.5 mm.

G

The screen for entering confirmation results for
the adjustment pattern is displayed.

When Standard is selected

Set the values printed under the patterns
selected in A and B, and then press the

Z

button.

When 100mm Pattern, 250mm Pattern, or
500mm Pattern is selected

Set the value established in step 6, and then
press the

Z

button.

When settings are complete, the status display
screen is displayed.

SC-F9300 Series User's Guide

Basic Operations

49

«
...
47
48
49
50
51
...
»

Содержание SC-F9300 series



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SC-F9300 series

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Parker Страницы: 54

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: Facsimile Страницы: 16

Бренд: EAW Страницы: 2

Бренд: abc Страницы: 28

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды