Epson SC-F9300 series Скачать руководство пользователя страница 114

Страница: 114 / 146

Printing does not stop when the roll
ends.

Is the item for having the printer detect the
end of the media set to Off?

When

Media End Check

is set to

Off

from the

Printer Setup menu, the end of the media is not
detected.

“The Printer Setup Menu” on page 99

Removing Jammed Media.

Follow the steps below to remove jammed media.

Caution:

Be careful not to trap your hands or fingers when
opening or closing the front cover. Failure to
observe this precaution could result in injury.

Turn off the printer.

If a message is displayed and the printer will
not turn off, unplug both power cables.

Open the front cover.

Move the media edge plates to the right and left
sides of the platen. Hold both tabs on the media
edge plates to move them.

Important:

Cease use of the printer if the media edge
plates are deformed. Continued use could
damage the pressure rollers or print head.

Contact your dealer or Epson Support.

If the print head is over the media, move it
away from the jam.

Important:

Move the print head only after moving the
media edge plates out of the way. Contact
with deformed media edge plates could
damage the print head.

Raise the media loading lever.

SC-F9300 Series User's Guide

Problem Solver

114

Содержание SC-F9300 series



















































































































































Результаты поиска

Содержание SC-F9300 series

Отзывы:

Похожие инструкции для SC-F9300 series

Бренды по названию

Популярные бренды

Epson SC-F9300 series, Руководство пользователя

Результаты поиска

Содержание SC-F9300 series

Отзывы:

Похожие инструкции для SC-F9300 series

Бренды по названию

Популярные бренды