manualshive.com logo in svg

Epson S1C63616, Техническое руководство

Epson S1C63616 - Техническое руководство для этого продукта доступно для бесплатной загрузки на manualshive.com. Получите подробное описание функций и спецификаций в руководстве пользователя. Не упустите возможность загрузить руководство, чтобы оптимизировать использование устройства.

Поделиться
Скачать
background image

SIC63616-(Rev. 1.0) NO. P125

3240-0412

4.10.6 Data input/output and interrupt function

The serial interface of S1C63616 can input/output data via the internal 8-bit shift register. The shift register 
operates by synchronizing with either the synchronous clock output from the SCLK (P20) terminal (master 
mode), or the synchronous clock input to the SCLK (P20) terminal (slave mode).
The serial interface generates an interrupt on completion of the 8-bit serial data input/output. Detection of 
serial data input/output is done by counting of the synchronous clock SCLK; the clock completes input/
output operation when 8 counts (equivalent to 8 cycles) have been made and then generates an interrupt.
The serial data input/output procedure is explained below:

Serial data output procedure and interrupt

The S1C63616 serial interface is capable of outputting parallel data as serial data, in units of 8 bits.
By setting the parallel data to the data registers SD0–SD3 and SD4–SD7 and writing "1" to SCTRG bit, it 
synchronizes with the synchronous clock and the serial data is output to the SOUT (P21) terminal. The 
synchronous clock used here is as follows: in master mode, internal clock which is output to the SCLK 
(P20) terminal while in slave mode, external clock which is input from the SCLK (P20) terminal.
Shift timing of serial data is as follows:

•  When positive polarity (SCPS1 = "0") is selected for the synchronous clock:

The serial data output to the SOUT (P21) terminal changes at the rising edge of the clock input or output 
from/to the SCLK (P20) terminal. The data in the shift register is shifted at the rising edge of the SCLK sig-
nal when the SCPS0 register is "0" or at the falling edge of the SCLK signal when the SCPS0 register is "1".

•  When negative polarity (SCPS1 = "1") is selected for the synchronous clock:

The serial data output to the SOUT (P21) terminal changes at the falling edge of the clock input or 
output from/to the SCLK (P20) terminal. The data in the shift register is shifted at the falling edge of 
the SCLK signal when the SCPS0 register is "0" or at the rising edge of the SCLK signal when the SCPS0 
register is "1".

When the output of the 8-bit data from SD0 to SD7 is completed, the interrupt factor flag ISIF is set to 
"1" and an interrupt occurs. Moreover, the interrupt can be masked by the interrupt mask register EISIF. 
However, regardless of the interrupt mask register setting, the interrupt factor flag is set to "1" after 
output of the 8-bit data. 

Serial data input procedure and interrupt

The S1C63616 serial interface is capable of inputting serial data as parallel data, in units of 8 bits.
The serial data is input from the SIN (P22) terminal, synchronizes with the synchronous clock, and is se-
quentially read in the 8-bit shift register. The synchronous clock used here is the internal clock in master 
mode or the external clock in slave mode.
Shift timing of serial data is as follows:

•  When positive polarity (SCPS1 = "0") is selected for the synchronous clock:

The serial data is read into the built-in shift register at the rising edge of the SCLK signal when the 
SCPS0 register is "0" or at the falling edge of the SCLK signal when the SCPS0 register is "1". The shift 
register is sequentially shifted as the data is fetched.

•  When negative polarity (SCPS1 = "1") is selected for the synchronous clock:

The serial data is read into the built-in shift register at the falling edge of the SCLK signal when the 
SCPS0 register is "0" or at the rising edge of the SCLK signal when the SCPS0 register is "1". The shift 
register is sequentially shifted as the data is fetched.

When the input of the 8-bit data from SD0 to SD7 is completed, the interrupt factor flag ISIF is set to 
"1" and an interrupt is generated. Moreover, the interrupt can be masked by the interrupt mask register 
EISIF. However, regardless of the interrupt mask register setting, the interrupt factor flag is set to "1" 
after input of the 8-bit data. 
The data input in the shift register can be read from data registers SD0–SD7 by software.

Содержание S1C63616







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C63616

Garmin GND 10 Installation Instructions preview
GND 10
Бренд: Garmin Страницы: 2
Oracle Talari E1000 Installation Manual preview
Talari E1000
Бренд: Oracle Страницы: 24
Patton electronics Model 2711 User Manual preview
Model 2711
Бренд: Patton electronics Страницы: 13
A4Tech RH-10 User Manual preview
RH-10
Бренд: A4Tech Страницы: 8
Technics SH-GE90 Service Manual preview
SH-GE90
Бренд: Technics Страницы: 20
IEI Technology PE-6S-R40 User Manual preview
PE-6S-R40
Бренд: IEI Technology Страницы: 4
Xtreme SNMP-1PMINI User & Installation Manual preview
SNMP-1PMINI
Бренд: Xtreme Страницы: 83
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Бренд: Vacron Страницы: 16
H3C SecPath F1070 Manual preview
SecPath F1070
Бренд: H3C Страницы: 68
CopperOptics 150-1342-01 Manual preview
150-1342-01
Бренд: CopperOptics Страницы: 12
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Бренд: Aaeon Страницы: 119
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Бренд: Avocent Страницы: 2
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Бренд: Grundfos Страницы: 40
Lattice Semiconductor mVision AR0234 User Manual preview
mVision AR0234
Бренд: Lattice Semiconductor Страницы: 25
Intel 80C186EC Manual preview
80C186EC
Бренд: Intel Страницы: 57
Renesas Emulation Probe M306V8T-EPB User Manual preview
Emulation Probe M306V8T-EPB
Бренд: Renesas Страницы: 90
MTI BR5811 User Manual preview
BR5811
Бренд: MTI Страницы: 41
FOR-A MFR-16SDI Installation Manual preview
MFR-16SDI
Бренд: FOR-A Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды