manualshive.com logo in svg

Epson S1C33210, Техническое руководство

Технический мануал для Epson S1C33210 доступен для бесплатного скачивания на manualshive.com. Пользователи могут легко загрузить этот мануал для получения дополнительной информации о продукте. Будьте в курсе всех особенностей и возможностей этого устройства, прочитав технический мануал.

Поделиться
Скачать
background image

III PERIPHERAL BLOCK: 16-BIT PROGRAMMABLE TIMERS

S1C33210 FUNCTION PART

EPSON

B-III-4-9

16-Bit Programmable Timer Interrupts and DMA

The 16-bit programmable timer has a function for generating an interrupt using the comparison match A and B
states.
The timing at which an interrupt is generated is shown in Figure 4.2 in the preceding section.

Control registers of the interrupt controller

Table 4.4 shows the control registers of the interrupt controller provided for each timer.

Table 4.4  Control Registers of Interrupt Controller

Interrupt factor

Interrupt factor flag

Interrupt enable register

Interrupt priority register

Timer 0 comparison A

F16TC0 (D3/0x40282)

E16TC0 (D3/0x40272)

P16T0[2:0] (D[2:0]/0x40266)

Timer 0 comparison B

F16TU0 (D2/0x40282)

E16TU0 (D2/0x40272)

Timer 1 comparison A

F16TC1 (D7/0x40282)

E16TC1 (D7/0x40272)

P16T1[2:0] (D[6:4]/0x40266)

Timer 1 comparison B

F16TU1 (D6/0x40282)

E16TU1 (D6/0x40272)

Timer 2 comparison A

F16TC2 (D3/0x40283)

E16TC2 (D3/0x40273)

P16T2[2:0] (D[2:0]/0x40267)

Timer 2 comparison B

F16TU2 (D2/0x40283)

E16TU2 (D2/0x40273)

Timer 3 comparison A

F16TC3 (D7/0x40283)

E16TC3 (D7/0x40273)

P16T3[2:0] (D[6:4]/0x40267)

Timer 3 comparison B

F16TU3 (D6/0x40283)

E16TU3 (D6/0x40273)

Timer 4 comparison A

F16TC4 (D3/0x40284)

E16TC4 (D3/0x40274)

P16T4[2:0] (D[2:0]/0x40268)

Timer 4 comparison B

F16TU4 (D2/0x40284)

E16TU4 (D2/0x40274)

Timer 5 comparison A

F16TC5 (D7/0x40284)

E16TC5 (D7/0x40274)

P16T5[2:0] (D[6:4]/0x40268)

Timer 5 comparison B

F16TU5 (D6/0x40284)

E16TU5 (D6/0x40274)

When a comparison match state occurs in the timer, the corresponding interrupt factor flag is set to "1".
If the interrupt enable register bit corresponding to that interrupt factor flag has been set to "1", an interrupt
request is generated.
An interrupt caused by a timer can be disabled by leaving the interrupt enable register bit for that timer set to
"0". The interrupt factor flag is always set to "1" by the timer's comparison match state, regardless of how the
interrupt enable register is set (even when set to "0").
The interrupt priority register sets an interrupt priority level (0 to 7) for each timer. Priorities within a timer
block are such that timers of smaller numbers have a higher priority. Priorities between interrupt types are such
that the comparison B interrupt has priority over the comparison A interrupt. An interrupt request to the CPU
is accepted only when no other interrupt request of a higher priority has been generated.
It is only when the PSR's IE bit = "1" (interrupts enabled) and the set value of the IL is smaller than the timer
interrupt level set by the interrupt priority register, that a timer interrupt request is actually accepted by the
CPU.
For details on these interrupt control registers, as well as the device operation when an interrupt has occurred,
refer to "ITC (Interrupt Controller)".

Intelligent DMA

The interrupt factor of each timer can also invoke intelligent DMA (IDMA). This allows memory-to-memory
DMA transfers to be performed cyclically.
The following shows the IDMA channel numbers set for each interrupt factor of timer:

IDMA Ch.

IDMA Ch.

Timer 0 comparison B:

0x07

Timer 0 comparison A:

0x08

Timer 1 comparison B:

0x09

Timer 1 comparison A: 0x0A

Timer 2 comparison B:

0x0B

Timer 2 comparison A: 0x0C

Timer 3 comparison B:

0x0D

Timer 3 comparison A: 0x0E

Timer 4 comparison B:

0x0F

Timer 4 comparison A:

0x10

Timer 5 comparison B:

0x11

Timer 5 comparison A:

0x12

Содержание S1C33210
















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C33210

Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Бренд: Paradyne Страницы: 2
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Бренд: Softing Страницы: 4
Rolls HR11C - SCHEMA Wiring Diagram preview
HR11C - SCHEMA
Бренд: Rolls Страницы: 1
Alula RE930R LTE M1 Install Manual preview
RE930R LTE M1
Бренд: Alula Страницы: 4
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Бренд: ZALMAN Страницы: 16
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Бренд: ekwb Страницы: 2
National Instruments IMAQTM User Manual preview
IMAQTM
Бренд: National Instruments Страницы: 121
ATI Technologies Radeon Online Manual preview
Radeon
Бренд: ATI Technologies Страницы: 87
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Бренд: VIA Technologies Страницы: 25
Flexwatch FW3870 User Manual preview
FW3870
Бренд: Flexwatch Страницы: 13
Harman Lexicon MPX 200 User Manual preview
Lexicon MPX 200
Бренд: Harman Страницы: 77
Nexus OSL101 Instructions Manual preview
OSL101
Бренд: Nexus Страницы: 9
Transition Networks E-BR-SIC User Manual preview
E-BR-SIC
Бренд: Transition Networks Страницы: 1
Abov A34M418YLN User Manual preview
A34M418YLN
Бренд: Abov Страницы: 8
U-Media WST-375L User Manual preview
WST-375L
Бренд: U-Media Страницы: 42
QSC DSP-3' Specification Sheet preview
DSP-3'
Бренд: QSC Страницы: 4
Axis T8120 Installation Manual preview
T8120
Бренд: Axis Страницы: 10
ARM Cordio BT4 Radio IP User Manual preview
Cordio BT4 Radio IP
Бренд: ARM Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды