Epson ActionPC 5000 Скачать руководство пользователя страница 81

Страница: 81 / 176

3. While holding down the

ALT

button, press the

LOAD/EJECT

button to adjust the loading position to a lower position on
the page; press the

LF/FF

button to adjust the loading

position to a higher position on the page. The

MULTI-PART

light stops blinking after a short time.

Note:

For continuous paper, the printer remembers this new position
even after it has been turned off and back on.

The printer has a minimum and maximum loading position. If

you try to advance the loading position beyond these limits, the
printer beeps and the paper stops moving.

When the paper reaches the factory-set loading position, the

printer beeps and paper feeding pauses briefly. Use the factory
set ting as a reference point when adjusting the loading position.

The printer remembers the new loading position for single- sheet

paper only until you turn off the power. The loading position

returns to the factory setting when the power is turned on again.

3-16 Using the Printer

Содержание ActionPC 5000

















































































































































































Результаты поиска

Содержание ActionPC 5000

Отзывы:

Бренды по названию

Популярные бренды

Epson ActionPC 5000, Руководство пользователя

Результаты поиска

Содержание ActionPC 5000

Отзывы:

Бренды по названию

Популярные бренды