Epson ActionPC 5000 Скачать руководство пользователя страница 28

Страница: 28 / 176

Installing the ribbon cartridge

Before installing the ribbon cartridge, make sure that the
power cord is not plugged into an electrical outlet.

1. Raise the paper-guide cover and rest it on the printer cover.

Lift the paper guide up and off. Lift the printer cover up
and off. Grasp both ends of the clear plastic paper-tension
unit; lift up the front of the unit and then lift it off.

Warning:

Never move the print head while the printer is turned

on;

this

can damage the printer. Also, if you just used the printer, the
print head may be hot. Let it cool for a few minutes before

touching it.

Setting Up the Printer 1-5

Содержание ActionPC 5000

















































































































































































Результаты поиска

Содержание ActionPC 5000

Отзывы:

Похожие инструкции для ActionPC 5000

Бренды по названию

Популярные бренды

Epson ActionPC 5000, Руководство пользователя

Результаты поиска

Содержание ActionPC 5000

Отзывы:

Похожие инструкции для ActionPC 5000

Бренды по названию

Популярные бренды