Epson ActionPC 5000 Скачать руководство пользователя страница 53

Страница: 53 / 176

Removing continuous paper from the push tractor

1. Press the

TEAR OFF

button to advance the paper to the

tear-off position. (See Chapter 3 for more information.)

Tear off any printed sheets.

Caution:

Always tear off paper before back-feeding; back-feeding too

many sheets can cause a paper jam.

2. Press the

LOAD/EJECT

button to feed the paper back to the

standby position.

3. Remove the paper from the tractor unit.

Loading continuous paper with the pull tractor

By placing the tractor in the pull-tractor position, you can load
paper from the rear, front, or bottom. The steps are the same
for all paper paths.

Note:

When the tractor is in the pull-tractor position, do not use the

TEAR-OFF

button or the

LOAD/EJECT

button to feed the paper back

fo the standby position.

1. Make sure the printer is turned off and the paper guide and

the printer cover are removed.

Paper Handling

2-15

Содержание ActionPC 5000

















































































































































































Результаты поиска

Содержание ActionPC 5000

Отзывы:

Epson ActionPC 5000, Руководство пользователя, Страница: 53 / 176

Результаты поиска

Содержание ActionPC 5000

Отзывы: