Epson Stylus PRO 7000 Скачать руководство пользователя страница 14

Страница: 14 / 182

1-6

The Control Panel

Status messages

The following messages show the printer status. For error
messages, see “Printer Stops Printing Unexpectedly” on page 6-3.

READY

Ready to print data.

POWER OFF

The power is off.

INK DRY
NN MIN

Drying ink after printing. Wait for “NN” minutes.

RESET

The printer is being reset.

PRESS PAUSE
BUTTON

The Pause button should be pressed.

PRINTING

Receiving print data.

WAIT

The printer is warming up, charging ink or
initializing.

PAUSE

The printer is paused. To resume printing, press
the Pause button.

NO INK CARTRIDGE

You are replacing the ink cartridge(s).

INK LOW

Ink cartridge(s) is (are) nearly empty. Replace
the ink cartridge(s) indicated by the Ink Out
light(s). When the ink cartridge(s) is (are) out,
printing stops. Printing can be resumed after
empty cartridge(s) have been replaced.

LOAD PAPER

The paper set lever is down while loading
paper. When you load paper and pull the set
lever up, PRESS PAUSE BUTTON appears.

TURN PWR OFF AND
ON

After clearing jammed paper, this message
appears. Turn the printer off and on.

INK CHARGING
nnn%

The printer is charging the ink delivery system.
This message shows the progress of the ink
charging process.

TRANSPORT PREP
nn%

The printer is preparing for transportation. This
message shows the progress of the preparation
process.

Содержание PRO 7000























































































































































































Результаты поиска

Содержание PRO 7000

Отзывы:

Бренды по названию

Популярные бренды

Epson Stylus PRO 7000, Справочное руководство

Результаты поиска

Содержание PRO 7000

Отзывы:

Бренды по названию

Популярные бренды