Epple Maschinen PW 30 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 50

background image

Stand 31.07.08, PW 30, PW 30 HV, Profile roll

Page 18 of 50

3.4

Positioning and assembly

3.4.1 Claims to installation location

The machine may not be in an explosive area. The machine is therefore
not  construed.  The  acceptable  environmental  conditions  have  to  be
followed  at  the  installation  location.  Organise  the  installation  location
according to the safety regulations for the use of this machine. See that
the  installation  location  is  not  limited  for  the  use,  attendance  and
maintenance.

Guarantee a boundless and free amenability of the mains plug and all
operation unit of the machine.

3.4.2 Load rope stops

The  machine  only  may  be  lifted  at  the  adequate  areas  with  adequate
lifting  device  and  load  rope  devices.  Observe  the  balance  point  of  the
machine.

Observe that during lifting no add

– on parts ort he lacquer get

damaged.

Machine weight
PW 30

191 kg

PW 30 HV

191 kg

In this case the manufacturer can not assume responsibility.

3.4.3 Positioning plan

Observe  during  the  positioning  of  the  machine,  that  the  design  of  the
work  place  is  ergonomic  and  follow  the  accident  prevention  regulations
for  your  business.  The  use,  attendance  and  maintenance  may  be  not
limited.
Bethink: A cramped work place recovers accident risks.

3.4.4 Positioning

Observe that the bottom/ ceiling are stable enough. If the rigidity is not
enough, it can come to oscillations between machine and bottom This can
lead to failures at the machine and adjoining units.

«
...
16
17
18
19
20
...
»

Содержание PW 30



















































Отзывы:

Нет отзывов

Похожие инструкции для PW 30

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Keithley Страницы: 149

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

Бренд: Hammer Strength Страницы: 18

Бренд: Wahl Страницы: 2

Бренд: J.P. SELECTA Страницы: 32

Бренд: Jet Страницы: 12

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Mako Страницы: 17

BOS R254K-UUI-LH10-S4

Бренд: Balluff Страницы: 12

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды