Epple Maschinen PW 30 Скачать руководство пользователя страница 20

Страница: 20 / 50

Stand 31.07.08, PW 30, PW 30 HV, Profile roll

Page 20 of 50

3.5

First initiation

Warning!

At the first initiation through inexperienced personnel you endanger the
personnel and property values. We do not assume accountability for defects that
were caused by an incorrect use, f. e. by inexperienced personnel.

3.5.1 Cleaning



Clean up all parts that were supplied with anticorrosion agent for

storage and transport with petroleum



The use of dissolvers, diluents for cell lacquer or other cleanser

agents that may attack the lacquer are improper.



Observe therefore the information of the cleanser agent manufacturer



Oil all bare machine parts; use therefore an acid

– free lubricant



Lubricate all movable parts

3.5.2 Sight check/ manual function check

Attenntion!

Machine may not be connected with grid!



Remove all transport lockings



Check whether the machine has visible defects



Check all mechanic components about smoothness



Check all control elements about mechanic function and smoothness

3.5.3 Electrical connection

The mains plug is correct pre

– assembled at the front side.



Check whether the circuit is accordant to the information of the

machine connection data.

3.5.4 Function check



Accomplish a safety check at the machine (view safety check at the

machine)



Let the machine run empty for one hour



Check the machine about bizarre sounds in both running directions



Check the temperature of the motor and the roller bearings



Let the machine run under load and check again about sound and

temperature

Содержание PW 30



















































Результаты поиска

Содержание PW 30

Отзывы:

Похожие инструкции для PW 30

Бренды по названию

Популярные бренды

Epple Maschinen PW 30, Руководство пользователя

Результаты поиска

Содержание PW 30

Отзывы:

Похожие инструкции для PW 30

Бренды по названию

Популярные бренды