29
I. Precautions
●
This unit is applied to the following discs:
Logo
2cm
1 2cm
12 cm
12 cm
12 cm
12cm
Disc size
It is applied to MP4 discs saved in the form of .avi, .dat.
It is applied to all functions of DVD VIDEO, DVD-R/ DVD-
RW or DVD+R/ DVD+RW under video mode.
It is applied to all functions of video CD or CD-R/ CD-RW under
video CD mode.
It is applied to all functions of music CD or CD-R/ CD-RW
under music CD mode.
I t i s a p p l i e d t o a l l f u n c t i o n s o f f i l e s s a v e d i n
C D - R O M / C D - R / C D - R W / D V D - R / D V D - R W /
It is applied to all functions of files saved in CD-ROM/
CD-R/ CD-RW/ DVD-R/ DVD-RW/ DVD+R/ DVD+RW in
Notes:
Mp4/ DVD/ VCD 1.0/ 1.1/ 2.0/ 3.0 versions, DVD, CD-R/ CD-RM/ MP3/ WMA/
JPEG/WMV/ MTV/ AVI/ MPG format discs are supported.
When playing DVD, VCD, MP3 or CD, the display screen will automatically
identify the disc and display corresponding samples. If the screen displays
“invalid”, it shows such function is unavailable under this mode, please select
another function. Refer to the instructions for specific operation.
●
●
●
●
●
●
●
●
Do not alter the unit yourself to avoid accident.
Playing disc in bumpy drive or playing non-standard or seriously damaged
disc can cause damage to the laser head.
Clean the laser head with laser head cleaning agent on a regular basis to
prevent from dust conglomeration.
Do not use the unit under a too high or too low temperature. Please make sure
that the temperature in car is between -20
~+60
before power-on.
If the screen displays the icon of
while operating, it shows that this
operation is not supported or is invalid.
In case of abnormal phenomenon, please refer to the part of
“Troubleshooting” of this manual. You may also press the “RES” button to
restore factory defaults.
℃
℃
1
2
Indications
Precautions:
◆
◆
◆
◆
◆
Ω
Make sure to insulate the exposed electric wires and well pack all wires to prevent
connecting terminal from contacting metal parts of the unit so as to avoid short
circuit.
If ACC position is unavailable to auto ignition system, please connect the ignition
lead to the “ON/ OFF” power supply with ignition switch key.
After power-on, the external amplifier control signals will be output through
AMP.CONT lead. If external amplifier is connected, please do not connect
AMP.CONT lead to amplifier power port to avoid electric leakage and fault.
The output terminal of the loud speaker is forbidden to be grounded, otherwise, it
may cause damage to the amplifier. Please avoid using 3 line type loud speaker
system with shared ground wire and connecting the speaker wire to the car body.
The loudspeaker connected to the unit must be of high power, and its minimum
rated voltage is 50w and resistance value is 4
. Do not connect directly the leads
of several loud speakers or use loud speaker with resistance value beyond the
limited scope, otherwise, it may lead to short circuit and cause damage to the loud
speaker.
◆
◆
◆
◆
◆
◆
◆
This unit is designed for negative ground 12V vehicle systems. Please install
proper dropping equipment if it is used in trucks, buses or coaches with 24V
systems.
Disconnect the negative terminal of the battery before installation to prevent from
short circuit.
Place the wire in fixable place to avoid contacting any mobile parts such as
handbrake and gear level. Do not place the wire in such hot areas as vicinity of
heat outlet to avoid short circuit arising from fusion or abrasion of wire insulating
layer.
Use required 10V fuse only when replacing. Use of high-capacity fuse or not use
of fuse may cause damage to the electric wire and lead to short circuit.
Do not lead the yellow wire through the mounting hole and into engine cabinet
before installing battery, otherwise, it may cause damage to the electric wire and
lead to short circuit.
Do not apply the wire of other equipments to this unit, otherwise, it may cause
overloading and lead to overheating.
Make sure to wrap the unused speaker lead wire with insulating tape to avoid
short circuit.
XIX. Connector Diagram
