background image

3

Safety Warnings & Recommendations

This manual is designed for the technician in conjunction with the owner’s manual. *

Please read this entire Technical Manual before installing or operating your Enviro Pellet Stove. 

Failure to follow these instructions may result in property damage, bodily injury or even death. 

Any unauthorized modification of the appliance or use of replacement parts not recommended 

by the manufacturer is prohibited. All national and local regulations shall be complied with 

when operating this appliance.

Caution: Do not connect to any air distribution duct or system.

Warning:

 Never place wood, paper, furniture, drapes or other combustible materials within 48” (122cm) 

of the front of the unit, 12” (30.5cm) from each side, and 3” (7.6cm) from the back of the unit. Do not let 

children or pets touch it when it is hot. 
To  prevent  the  possibility  of  a  fire,  ensure  that  the  appliance  is  properly  installed  by  adhering  to  the 

installation instructions. An Enviro dealer will be happy to assist you in obtaining information with regards 

to your local building codes and installation restrictions.

FIRE EXTINGUISHER AND SMOKE DETECTION: 

All homes with a pellet burning stove should have at 

least one fire extinguisher in a central location known to all in the household. Smoke detectors should be 

installed and maintained in the room containing the stove. If it sounds the alarm, correct the cause but do 

not deactivate. You may choose to relocate the smoke detection devise within the room; DO NOT REMOVE 

THE SMOKE DETECTOR FROM THE ROOM.

CHIMNEY OR RUN AWAY FIRE: 

Call local fire department (or dial 911). Close the draft fully. Extinguish 

the fire in the burn pot liner with a cup of water and close the door. Examine the flue pipes, chimney, attic, 

and roof of the house, to see if any part has become hot enough to catch fire. If necessary, spray with fire 

extinguisher or water from the garden hose. IMPORTANT:

 

Do not operate the stove again until you are 

certain the chimney and its lining have not been damaged.

OPERATION:

 The door and ash drawer must be kept closed when the unit is in operation to prevent 

fume spillage and for proper and safe operation of the pellet stove. Also ensure all gaskets on the door 

are checked and replaced when necessary. 

Unit hot while in operation. Keep children, clothing and 

furniture away. Contact may cause skin burns.
CAUTION: 

When operating during adverse weather, if the unit exhibits dramatic changes in combustion 

stop using the unit immediately. 

FUEL

:  This stove is designed and approved to only burn wood pellets of any quality, corn, wheat, and 

barley.  Dirty fuel will adversely affect the operation and performance of the unit and may void the warranty. 

Check  with  your  dealer  for  fuel  recommendations. 

THE  USE  OF  CORD  WOOD  IS  PROHIBITED  BY 

LAW. Do not burn garbage or flammable fluids such as gasoline, naphtha or engine oil.
SOOT:

 Operation of the stove with insufficient combustion air will result in the formation of soot which will 

collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house.  

Frequently check your stove and adjust the slider/damper as needed to ensure proper combustion. 

See: 

S

lider

/d

amper

 S

etting

”.

CLEANING:

 There will be some build up of fly ash and small amounts of creosote in the exhaust. This will 

vary due to the ash content of the fuel used and the operation of the stove. It is advisable to inspect and 

clean the exhaust vent semi-annually or every two tons of pellets.
The appliance, flue gas connector and the chimney flue require regular cleaning. Check them for blockage 

prior to re-lighting after a prolonged shut down period.

ASHES:

 Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container 

of ashes should be on a non-combustible surface, well away from all combustible materials pending final 

disposal. If the ashes are disposed of by burial in soil or otherwise locally dispensed, they should be retained 

in the closed container until all cinders have thoroughly cooled.

Содержание M55C-FPI

































Отзывы: