background image

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY 

THIS MANUAL IS PRINTED ON RECYCLED PAPER

 

 

 

 

 

 

 

 

 

 

EG 28 B Vented 

                B y  

S H E R W O O D  

I N D U S T R I E S  

O W N E R S   M A N U A L  

 
 

 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

WHAT TO DO IF YOU SMELL GAS 

 Open windows 

 Do not try to light any appliance. 

 Do not touch any electrical switch; do not use any phone 

in your building. 

 Immediately call your gas supplier from a neighbor's 

phone.  Follow the gas supplier's instructions. 

 If you cannot reach your gas supplier, call the fire 

department. 

WARNING

 

If the information in this manual is 

not followed exactly, a fire or 

explosion may result causing 

property damage, personal injury 

or loss of life installation and 

service must be performed by a 

qualified installer, service agency 

or the gas supplier. 

FOR YOUR SAFETY 

Do not store or use gasoline or other 

Flammable

 vapors and liquids in the vicinity of 

this or any other appliance. 

Massachusetts installations

 (WARNING): 

This product must be installed by a licensed plumber or gas fitter when installed within the 

Commonwealth of Massachusetts. Other Massachusetts code requirements: Flexible connector must not be longer than 36”, shutoff valve 
must be a “T” handle gas cock, only direct vent sealed combustion products are approved for bedroom/bathrooms, fireplace dampers must 
be removed or welded in the open position prior to the installation of a fireplace insert or gas log. 

Содержание EG 28 B





















Отзывы: