manualshive.com logo in svg

Entrematic LCU40H, Руководство по установке, Страница: 43 / 46

Поделиться
Скачать
Entrematic LCU40H Скачать руководство пользователя страница 43

43

IP2246EN

Type of 

alarm

Display

Description

Operation

Internal c

ontr

ol panel alarm

I5 - No voltage 0-1 (faulty voltage regulator 
or short-circuit on accessories)

Check there is no short-circuit in connec-
tion 0-1.
If the problem persists, replace the control 
panel.

I6 - Excessive voltage 0-1 (faulty voltage 
regulator)

Replace the control panel.

I7 - Internal parameter error - value out-
side limits

Reset.
If the problem persists, replace the con-
trol panel.

I8 - Program sequence error

Reset.
If the problem persists, replace the con-
trol panel.

IA - Internal parameter error (EEPROM/
FLASH)

Reset.
If the problem persists, replace the con-
trol panel.

IB - Internal parameter error (RAM)

Reset.
If the problem persists, replace the con-
trol panel.

IC - Operation time-out error (>5 min or 
>7 min in learning mode)

Manually check that the gate wing moves 
freely.
If the problem persists, replace the con-
trol panel.

IE - Power supply circuit fault

Reset. 
If the problem persists, replace the control 
panel.

IM - MOSFET alarm - motor 1 in short-cir-
cuit or always ON

Reset.
Check the settings / operating of any limit 
switches.
If the problem persists, replace the con-
trol panel.

IN - MOSFET alarm - motor 2 in short-cir-
cuit or always ON

Reset.
If the problem persists, replace the con-
trol panel.

IO - Interrupted power circuit - motor 1 
(motor MOSFET open or always OFF)

Reset.
If the problem persists, replace the con-
trol panel.

IP - Interrupted power circuit - motor 2 
(motor MOSFET open or always OFF)

Reset.
If the problem persists, replace the con-
trol panel.

IS - Error on current read circuit test - mo-
tor 1

Reset.
If the problem persists, replace the control 
panel.

IT - Error on current read circuit test - mo-
tor 2

Reset.
If the problem persists, replace the control 
panel.

IU - Error on voltage read circuit test - 
motor 1

Reset.
If the problem persists, replace the control 
panel.

IV - Error on voltage read circuit test - 
motor 2

Reset.
If the problem persists, replace the control 
panel.

XX - Firmware reset commanded by the simultaneous pressing of the         

  +

  

 keys.

WD - Firmware reset not commanded

Содержание LCU40H















































Отзывы:

Нет отзывов