Enterasys Matrix 7G4202-30 Скачать руководство пользователя

Страница: 77 / 110

Using LANVIEW

Troubleshooting

4-3

Table 4-1

LANVIEW LEDs

LED

Color

State

Recommended Action

MGMT

None

Off

. This module is NOT

the Management Module.

None.

Green

Solid

. This module is the

designated Management
Module.

None.

Amber

Flashing

This is a

temporary

indication that

the module is saving
data.

None.

CPU

None

Power off.

Ensure chassis has adequate power.

Amber

Blinking

. Module in

process of booting.

None.

Solid

. Testing.

If the LED remains amber for several
minutes, contact Enterasys Networks for
technical support.

Green

Blinking

Image starts

running.

None.

Solid

. Functional.

None.

Red

Solid

. Processor in reset.

None.

Green
and
Amber

Blinking

Indicates that

the DFE module is in the
process of shutting down.

None. This state is activated when the
RESET button is pressed for less than
1 second to a start the process of an orderly
shutdown.

While in this state, do not remove any DFE
module.

Содержание Matrix 7G4202-30















































































































Результаты поиска

Содержание Matrix 7G4202-30

Отзывы:

Похожие инструкции для Matrix 7G4202-30

Бренды по названию

Популярные бренды

Enterasys Matrix 7G4202-30, Руководство по установке оборудования

Результаты поиска

Содержание Matrix 7G4202-30

Отзывы:

Похожие инструкции для Matrix 7G4202-30

Бренды по названию

Популярные бренды