Enterasys Matrix 7G4202-30 Скачать руководство пользователя | Manualshive

Страница: 48 / 110

background image

Installing Module into Matrix E7 or N7 Chassis

3-12

Installation

Installation

To install the module, refer to

Figure 3-5

and proceed as follows:

1.

Locate the chassis card guides that line up with the slot number in which the module

➂

will be

installed. Make sure the module locking levers are in the open position (top and bottom).

2.

Align the module card between the upper and lower card guides of the desired slot and slide it
into the chassis, taking care that the module slides in straight. See Caution below.

3.

Slide the module into the slot until you can engage the top and bottom locking levers with the
chassis as shown in

Figure 3-5

.

4.

Refer to the Caution note above, then rotate the two levers into the closed position .

5.

If the chassis in which the module is installed was powered down for the installation, turn the
power supplies on. Check to see that the module CPU LED settles at solid green after a few
minutes. If the LED does not turn solid green, refer to

Chapter 4

for troubleshooting details.

Caution:

To prevent damaging the backplane connectors in the following step, take

care that the module slides in straight and properly engages the backplane connectors.

Ensure that the top lever lines up with the desired slot number located on the front panel
of the chassis. Refer to

Figure 3-5

.

Precaución:

Para evitar que se dañen los conectores del panel posterior en el siguiente

paso, intente deslizar el módulo en forma recta y verifique que se enganche
correctamente en los conectores de panel posterior.

Asegúrese de que la palanca superior esté alineada con respecto al número de ranura
correspondiente ubicado en el panel frontal del chasis. Consulte en

Figure 3-5

.

Caution:

Due to the amount of force needed to properly seat the module connectors

into the backplane connectors, it is best to apply force to the end of the levers to insert
(or eject) the module. Otherwise, damage could result to the module and chassis.

Precaución:

Para colocar los conectores del módulo en los conectores del panel

posterior correctamente es necesario hacer bastante fuerza, por ello, para insertar o
quitar el módulo, se recomienda concentrar la fuerza en el extremo de las palancas. Si
no lo hace, podría dañar el módulo y el chasis.

Caution:

In step 4, do not force the locking levers to the point that they touch the face of

the front panel. Forcing the locking levers to this point could damage the module and
chassis.

Precaución:

En el paso 4, tenga cuidado de no llevar las palancas de cierre a un punto

en donde estén en contacto con el panel frontal. Si lo hace, podría dañar el módulo y/o
el chasis.

«
...
46
47
48
49
50
...
»

Содержание Matrix 7G4202-30















































































































Отзывы:

Нет отзывов

Похожие инструкции для Matrix 7G4202-30

Бренд: Ubiquiti Страницы: 50

Бренд: NETGEAR Страницы: 169

Бренд: NetBurner Страницы: 15

Бренд: 3Com Страницы: 18

Бренд: Supermicro Страницы: 24

Бренд: Ruckus Wireless Страницы: 56

Бренд: Renesas Страницы: 6

IAR KickStart Kit TWR-K60N512-IAR

Бренд: IAR SYSTEMS Страницы: 8

Бренд: Allied Telesis Страницы: 22

Бренд: U.S. Products Страницы: 80

Бренд: Cypress Semiconductor Страницы: 16

Бренд: Gbord Страницы: 8

Speedway Revolution

Бренд: impinj Страницы: 60

Бренд: National Instruments Страницы: 8

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

Бренд: Moxa Technologies Страницы: 51

Бренд: ActionTec Страницы: 115

FlexNetwork 5130 Series

Бренд: HPE Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды