Enterasys Matrix 7G4202-30 Скачать руководство пользователя | Manualshive

Страница: 42 / 110

background image

Installing an Optional Mini-GBIC

3-6

Installation

Removing the Mini-GBIC

To remove a Mini-GBIC from a

port slot, proceed as follows:

1.

Attach the antistatic wrist strap (refer to the instructions in the antistatic wrist strap package)
before removing the Mini-GBIC.

2.

Remove the cables connected to the Mini-GBIC.

3.

Release the Mini-GBIC from the port slot. Refer back to the appropriate figure listed below to
locate the release mechanism and proceed as instructed.

-

For the type of Mini-GBIC shown in

Figure 3-1

, push in on the release tab as far as it will go

to release the Mini-GBIC.

-

For the type of Mini-GBIC shown in

Figure 3-2

, pull out on the release tab to release the

Mini-GBIC.

-

For the type of Mini-GBIC shown in

Figure 3-3

, pull down on the wire handle to release the

Mini-GBIC.

4.

Grasp the sides of the Mini-GBIC and pull it straight out of the port slot.

If storing or shipping the Mini-GBIC, insert its dust protector to protect its fiber-optic ports.

Caution:

Do NOT remove a Mini-GBIC from a slot without releasing the locking tab

located under the front bottom end of the Mini-GBIC

.

This can damage the Mini-GBIC.

The Mini-GBIC and its host device are sensitive to static discharges. Use an antistatic
wrist strap and observe all static precautions during this procedure. Failure to do so
could result in damaging the Mini-GBIC or host device. Always leave the Mini-GBIC in
the antistatic bag or an equivalent antistatic container when not installed.

Precaución:

NO quite el Mini- GBIC de la ranura sin antes abrir la traba ubicada en la

parte frontal del Mini- GBIC.

Si lo hace, puede dañar el Mini- GBIC, puesto que es muy sensible a las descargas de
electricidad estática, al igual que el dispositivo host. Utilice la pulsera antiestática y
tome todas las precauciones necesarias durante este procedimiento. Si no lo hace,
pude dañar el Mini- GBIC o el dispositivo host. Mientras no esté instalado, mantenga el
Mini- GBIC en su bolsa antiestática o en cualquier otro recipiente antiestático.

«
...
40
41
42
43
44
...
»

Содержание Matrix 7G4202-30















































































































Отзывы:

Нет отзывов

Похожие инструкции для Matrix 7G4202-30

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

SmartSwitch Router

Бренд: Cabletron Systems Страницы: 338

Бренд: Yamaha Страницы: 4

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: Keithley Страницы: 59

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды