manualshive.com logo in svg

ENSTROM 280F Series, Руководство по обслуживанию

Maintenance Manual для серии ENSTROM 280F - это обязательный ресурс для владельцев вертолетов. Скачайте его бесплатно на manualshive.com и получите все необходимые инструкции и рекомендации по техническому обслуживанию. Надежность и безопасность вашего вертолета - наш приоритет.

Поделиться
Скачать
background image

ENSTROM F-28F/280F SERIES MAINTENANCE MANUAL 

  

Rev. 

7 

 MM-9-25 

Aug 

22/16 

E. 

Main Rotor Hub – Assembly  (See Figure 9-3) 

 

WARNING:  Use extreme caution when removing or installing the blade and grip 

assemblies to prevent from injuring personnel. 

 

WARNING:  Use protective gloves when handling heated parts. 

 

NOTE:  The upper hub plate has helicoil inserts in the outer bosses for the 

walking beam mount brackets. The lower hub plate bosses are solid. 

 

(1)  Heat the upper hub plate (14) and the lower hub plate (17) to approximately 

250°F/121°C. 

 

(2)  Place the lower hub plate on 2" X 4" wood blocks. Lubricate the bearing bores with 

MIL-PRF-81322. 

 

NOTE: 

Ensure the DU washers have been installed on the U-blocks with the 
chamfered side facing the hub plates. The DU washers must be seated 
in the recessed area of the hub plate. 

 

(3)  Install the U-block (universal block) assemblies (15) into the bearing bore of the hub 

plate with the threaded notched end of the U-blocks down (3 places). 

 

(4) 

Place the spacer (16) on the lower hub plate and align the bolt holes. 

 

NOTE: 

Ensure the DU washers are seated in the recessed areas of the upper 
hub plate. 

 

(5)  Lubricate the bearing bores of the upper hub plate and install the upper hub plate 

onto the U-blocks. 

 

NOTE: 

The dowel pins must be installed until slightly recessed from face of 
hub plate surface. 

 

(6)  Lubricate the dowel pins (13) and tap pins into the center hole of the 3-hole bolt 

pattern (3 places). 

 

NOTE: 

The upper spline adapter has the wider flat surface on the top side of 
the splines while the lower adapter has a rib extending from the lower 
end of the splines. 

 

CAUTION:  When installing spline adapters, the phasing marks on top of the 

splines must align with one of the walking beam mount brackets (3). 
Using a felt marker, mark a line on outboard edge of hub plate in line 
with spline phasing marks to aid in the alignment when installing 
lower spline adapter. 

 

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Visit www.enstromhelicopter.com for instructions to order an original manual and to register for email notification of updates.

Содержание 280F Series























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 280F Series

Gayla 640 Assembly Instructions preview
640
Бренд: Gayla Страницы: 2
HobbyBoss Mi-2T Hoplite Manual preview
Mi-2T Hoplite
Бренд: HobbyBoss Страницы: 8
LCUT Creative B 00-26 Quick Start Manual preview
B 00-26
Бренд: LCUT Creative Страницы: 2
Eduard Bf 109E-4 interior S.A. Manual preview
Bf 109E-4 interior S.A.
Бренд: Eduard Страницы: 4
Uctronics Smart Bluetooth Robot Car User Manual preview
Smart Bluetooth Robot Car
Бренд: Uctronics Страницы: 42
VTech Toot-Toot Drivers CustomisablePeople Carrier User Manual preview
Toot-Toot Drivers CustomisablePeople Carrier
Бренд: VTech Страницы: 11
Jamara Lucky Instruction preview
Lucky
Бренд: Jamara Страницы: 8
SAB Heli Division Goblin RAW 700 Manual preview
Goblin RAW 700
Бренд: SAB Heli Division Страницы: 48
K'Nex 79520 Manual preview
79520
Бренд: K'Nex Страницы: 36
B.toys Happy Cruisers BX1781Z Quick Start Manual preview
Happy Cruisers BX1781Z
Бренд: B.toys Страницы: 2
VTech Brainy Baby Number Bug User Manual preview
Brainy Baby Number Bug
Бренд: VTech Страницы: 9
Power Wheels J8760 Owner'S Manual With Assembly Instructions preview
J8760
Бренд: Power Wheels Страницы: 32
B.toys B,play Poppity Whale Pop Quick Start Manual preview
B,play Poppity Whale Pop
Бренд: B.toys Страницы: 2
Eduard C-130J-30 interior Assembly Instructions preview
C-130J-30 interior
Бренд: Eduard Страницы: 4
Aeronaut Twinspeedy Manual preview
Twinspeedy
Бренд: Aeronaut Страницы: 5
Alexander Origami 3D Fox 2575 Manual preview
Origami 3D Fox 2575
Бренд: Alexander Страницы: 68
Estes Sky Writer Instruction Manual preview
Sky Writer
Бренд: Estes Страницы: 4
PalPlay The House of Fun M780 Assembly Instructions Manual preview
The House of Fun M780
Бренд: PalPlay Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды