manualshive.com logo in svg

ENSTROM 280F Series, Руководство по обслуживанию

Поделиться
Скачать
ENSTROM 280F Series Скачать руководство пользователя страница 231

ENSTROM F-28F/280F SERIES MAINTENANCE MANUAL 

 

  

Rev. 

8 

 MM-8-37 

Sep 

20/17 

E.  Landing Gear Fairings (280FX) 

280FX models are equipped with landing gear fairings on the oleo struts and landing gear 
legs. These fairings are made of aluminum and fiberglass and are clamped onto the landing 
gear assembly. To check for proper strut extension, the helicopter should be sitting on level 
ground. The struts should then be leveled by rocking the helicopter by pushing up and 
down slightly on the tail cone. For the checking method, see Section 4-20; for proper 
inflation, see Section 4-20, Item A. 

NOTE: 

For a float installation, the complete fairing assemblies must be removed. Prior 
to mount clamp removal, their position should be marked for ease of 
reinstallation. 

1.  Removal – Access to Service Oleo Strut 

(a)  Remove 3 screws (9) from upper flex boot (6) lower end. 

(b)  Lift flex boot (6) upward to expose oleo valve for required servicing see Section 4-20 

Item 1. 

2.  Removal – Access for Oleo Strut Removal 

(a)  Proceed with paragraph 1, steps (a) and (b). 

(b)  Remove 2 screws (10) front and back, top and bottom of oleo fairing (2). 

(c)  Slip rubber boot (4) at bottom of fairing (2) downward to clear attaching screws. 

(d)  Remove screws (5) from trailing edge of fairing (2). 

(e)  Spread fairing (2) carefully to clear oleo and remove from forward side. 

(f) 

Remove 4 screws (7) and bolt (8) from lower fairing (1) or (3). 

(g)  To remove forward fairing (1) carefully spread to clear gear and oleo remove from 

forward side. 

(h)  To remove aft lower fairing (3) carefully spread to clear gear and oleo and slip 

forward on drag strut. 

(i) 

Remove oleo as described in Section 8-9, paragraph D. 

3. Inspection 

(a)  Check for cracked or damaged components and replace as required. 

(b)  Check for missing nut plates and screws replace as required. 

 

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Visit www.enstromhelicopter.com for instructions to order an original manual and to register for email notification of updates.

Содержание 280F Series























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды