manualshive.com logo in svg

ENSTROM 280F Series, Руководство по обслуживанию

Maintenance Manual для серии ENSTROM 280F - это обязательный ресурс для владельцев вертолетов. Скачайте его бесплатно на manualshive.com и получите все необходимые инструкции и рекомендации по техническому обслуживанию. Надежность и безопасность вашего вертолета - наш приоритет.

Поделиться
Скачать
background image

ENSTROM F-28F/280F SERIES MAINTENANCE MANUAL 

  

Rev. 

4 

 MM-4-70 

Jun 

21/12 

4-71. Hoisting  

(Figure 4-3)

 

A.  If the main rotor hub is installed, install the lifting sling (T-0011) so that the arms are 

between the pitch arm and the blade retention assembly, over the lead/lag retaining nut, and 
outboard of the main rotor damper rod-end.  The sling arms are long enough to be double 
rapped if preferred. 

 

B.  If the main rotor hub is removed, install the lifting eye (T-0017) onto the main rotor 

mast.

warning

The lifting device must have a lifting rating equal to or greater than the 
actual weight of the aircraft to be hoisted. 

 

C.  Connect a suitable lifting device to the lifting sling or eye. 

 

D.  Station a person at the tail rotor guard to steady the aircraft when hoisted.  If lifting 

beyond reach from the ground, two people and two steadying ropes will be necessary. 

 

E.  Slowly hoist the aircraft using a steady lifting force. 

4-72. Cleaning 

4-73. Exterior – Cleaning 

NOTE 

The exterior of the aircraft is painted with a high quality paint.  Proper 
maintenance of this finish will provide corrosion protection as well as an 
attractive finish. 

NOTE 

Do not wash the aircraft using pressure washing equipment. 

 

A.  Wash the exterior as follows: 

 

 

(1)  Check the security of all doors and access panels before starting the washing 

operation.

 

 

(2)  Flush the entire aircraft free of dirt. 

NOTE 

Avoid direct spraying of the main rotor hub, tail rotor assembly, and tail rotor 
driveshaft bearings to prevent the loss of lubricant.  These areas should be 
purged with grease after washing to eliminate any moisture. 

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Visit www.enstromhelicopter.com for instructions to order an original manual and to register for email notification of updates.

Содержание 280F Series























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 280F Series

Faller 130165 Quick Start Manual preview
130165
Бренд: Faller Страницы: 8
Hobbies & Helis Quick 50 Pro Assembly & Parts Listing preview
Quick 50 Pro
Бренд: Hobbies & Helis Страницы: 60
INTERACTIVE TOY CONCEPTS GOOSE HUNTER Instruction Manual preview
GOOSE HUNTER
Бренд: INTERACTIVE TOY CONCEPTS Страницы: 2
Ozone r1 v2 Manual preview
r1 v2
Бренд: Ozone Страницы: 20
Stevens AeroModel SkyBuggy Manual preview
SkyBuggy
Бренд: Stevens AeroModel Страницы: 30
Jamara Floater Altitude 2,4 GHz Instruction preview
Floater Altitude 2,4 GHz
Бренд: Jamara Страницы: 12
Faller 190287/1 Instructions Manual preview
190287/1
Бренд: Faller Страницы: 12
Fisher-Price G2579 The Incredibles Instruction Manual preview
G2579 The Incredibles
Бренд: Fisher-Price Страницы: 10
VTech Baby Amaze Peek & Learn Doll User Manual preview
Baby Amaze Peek & Learn Doll
Бренд: VTech Страницы: 12
Hirobo 4512895160081 Instruction Manual preview
4512895160081
Бренд: Hirobo Страницы: 52
Tabletop Scenics TTSC-WAR-081 Instruction Manual preview
TTSC-WAR-081
Бренд: Tabletop Scenics Страницы: 88
Dream Sports 24 Pop-up Football Goal 2-in-1 User Manual preview
Pop-up Football Goal 2-in-1
Бренд: Dream Sports 24 Страницы: 16
Fisher-Price 77198 Instructions Manual preview
77198
Бренд: Fisher-Price Страницы: 20
A4 SoLDrag Manual preview
SoLDrag
Бренд: A4 Страницы: 20
LIGHT MY BRICKS Volkswagen Beetle LED Lighting Kit Manual preview
Volkswagen Beetle LED Lighting Kit
Бренд: LIGHT MY BRICKS Страницы: 15
marklin 37218 User Manual preview
37218
Бренд: marklin Страницы: 32
Team Losi Micro-T Operation Manual preview
Micro-T
Бренд: Team Losi Страницы: 7
K'Nex Imagine-Build-Play SWING RIDE Manual preview
Imagine-Build-Play SWING RIDE
Бренд: K'Nex Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды