manualshive.com logo in svg

ENSTROM 280F Series, Руководство по обслуживанию

Maintenance Manual для серии ENSTROM 280F - это обязательный ресурс для владельцев вертолетов. Скачайте его бесплатно на manualshive.com и получите все необходимые инструкции и рекомендации по техническому обслуживанию. Надежность и безопасность вашего вертолета - наш приоритет.

Поделиться
Скачать
background image

ENSTROM F-28F/280F SERIES MAINTENANCE MANUAL 

  

Rev. 

8 

 viii 

Sep 

20/17 

13-5. Turbocharger 

.........................................................................................MM-13-47 

13-6. 

Turbocharger Static Air Fuel Nozzle Pressure System ......................... MM-13-49 

13-7. Primary 

Airflow 

System 

......................................................................... 

MM-13-52 

13-8. Cooling 

System 

..................................................................................... 

MM-13-57 

13-9. Ignition 

System...................................................................................... 

MM-13-64 

13-10. Fuel 

System 

.......................................................................................... 

MM-13-72 

13-11. Lubricating 

System 

................................................................................MM-13-88 

13-12. Correlator 

.............................................................................................. 

MM-13-94 

Section 14 – Utility Systems 

14-1. Cabin 

Heat 

.............................................................................................. 

MM-14-1 

MAINTENANCE MANUAL SUPPLEMENT 280FX & 1986 F-28F – SECTIONS 15 THROUGH 25 

Section 15 – Supplemental Procedures 

15-1. Introduction 

............................................................................................. 

MM-15-1 

15-2. 

Table of Contents .................................................................................... MM-15-1 

15-3. 

Manual Changes and Revisions ............................................................. MM-15-1 

Section 16 – [Reserved] 

Section 17 – [Reserved] 

Section 18 – Powerplant 

18-1. General 

................................................................................................... 

MM-18-1 

Section 19 – Main Rotor Transmission 

19-1. General 

................................................................................................... 

MM-19-1 

19-2. 

Main Rotor Gearbox Chip Detector ......................................................... MM-19-1 

19-3. Lubricant 

Change 

.................................................................................... 

MM-19-2 

Section 20 – Belt Drive System 

20-1. General 

Information 

................................................................................ 

MM-20-1 

Section 21 – Electrical Systems and Components 

21-1. General 

................................................................................................... 

MM-21-1 

21-2. 

Combined Anticollision and Navigation Lights ........................................ MM-21-1 

21-3. Annunciator 

Panel 

................................................................................... 

MM-21-1 

21-4. 

Anticollision and Navigation Light and Annunciator Panel 

 Troubleshooting 

Chart 

.............................................................................MM-21-6 

21-5. 

Lamp/Assembly Replacement Guide Chart ............................................ MM-21-8 

21-6. 

Ampere Load Conditions .........................................................................MM-21-8 

21-7. 

Hi/Lo Rotor RPM Warning System ........................................................MM-21-11 

21-8. Schematic 

Diagrams 

............................................................................. 

MM-21-14 

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Visit www.enstromhelicopter.com for instructions to order an original manual and to register for email notification of updates.

Содержание 280F Series























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 280F Series

GAME OF BRICKS 21332 Instruction Manual preview
21332
Бренд: GAME OF BRICKS Страницы: 47
K'Nex 80216 Manual preview
80216
Бренд: K'Nex Страницы: 32
K'Nex 79520 User Manual preview
79520
Бренд: K'Nex Страницы: 24
Stevens AeroModel SkyBuggy Manual preview
SkyBuggy
Бренд: Stevens AeroModel Страницы: 30
K'Nex Education STEM Explorations 79320 Instruction Book preview
Education STEM Explorations 79320
Бренд: K'Nex Страницы: 16
Slackers Slide&Surf SLA.747757 Instructions And Safety Rules preview
Slide&Surf SLA.747757
Бренд: Slackers Страницы: 3
Dancing Wings Hobby SCG21 Instruction Manual preview
SCG21
Бренд: Dancing Wings Hobby Страницы: 6
Liliput L13351x Operating Manual preview
L13351x
Бренд: Liliput Страницы: 7
Eduard 32 163 Instruction Sheet preview
32 163
Бренд: Eduard Страницы: 3
LEGO CITY 60058 Building Instructions preview
CITY 60058
Бренд: LEGO Страницы: 44
Faller CAR SYSTEM CONVERSION CHASSIS LORRY MB CITARO 162034 Assembly Instructions preview
CAR SYSTEM CONVERSION CHASSIS LORRY MB CITARO 162034
Бренд: Faller Страницы: 2
4-Max SpinRay Building Instructions preview
SpinRay
Бренд: 4-Max Страницы: 8
Fisher-Price BJT74 Manual preview
BJT74
Бренд: Fisher-Price Страницы: 16
Faller 190138/1 Instructions Manual preview
190138/1
Бренд: Faller Страницы: 8
Radio Shack Star Navigator Owner'S Manual preview
Star Navigator
Бренд: Radio Shack Страницы: 16
Chicco 00 000906 000 000 Instructions Manual preview
00 000906 000 000
Бренд: Chicco Страницы: 16
PARKZONE Ultra Micro F-27Q Stryker 180 Instruction Manual preview
Ultra Micro F-27Q Stryker 180
Бренд: PARKZONE Страницы: 21
Magformers 32 XL CRUISER Manual preview
32 XL CRUISER
Бренд: Magformers Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды