manualshive.com logo in svg

EnOcean STM110C, Руководство пользователя

Поделиться
Скачать
EnOcean STM110C Скачать руководство пользователя страница 7

USER MANUAL 

V0.904 

EnOcean GmbH 
Kolpingring 18a 
82041 Oberhaching 
Germany 

Phone +49.89.67 34 689-0 
Fax +49.89.67 

34 

689-50 

[email protected] 
www.enocean.com 

Subject to modifications 
STM110C User Manual V0.904 
February 18, 2008 2:00 PM 
Page 6/40 

 

STM110C 

1.3

 

Technical Data 

 

Power supply 

Solar Power Generator (discrete optical cell), or 2.2 - 5.0V external 

Frequency / Conducted transmission power 

315.0 MHz / 12dBm 

Data rate / Modulation type 

125 kbps / ASK 

Transmission range  

300m free field, typ. 30m indoor 

Module identifier 

individual 32-bit ID factory-programmed 

EnOcean telegram type 

4BS (“Four Byte Sensor”) 

Telegram packet length (sub-telegram) 

1.2 ms 

±

5% 

No. of (redundant) packets 

3 packets within about 40ms, delay effected at random 

Input channels 

3 x analog inputs (8-bit resolution), 4 x digital inputs 

Spontaneous wake-up 

differential external trigger signal, minimum wake interval 7ms 

Cyclic wake-up 

user-configurable (every 1, 10, 100, or 110 s, tolerance ± 20%) 

Redundant retransmission 

user-configurable, affected at random 

Illumination 

100 lx up to 100.000 lx 

Operation startup time with empty energy store 

< 10 min @ 400 lx 

Operation time during total darkness 

> 60 h 

1)

 

1)

 storage is filled @ 1000 lx (4.2V in Goldcap)

RF transmission statistically every 17 min, 100s wake-up, temperature 25°C, Goldcap formatted

 Ext. power supply output 

3.0 V ±3%, 1mA max., ~2.6ms (during wake-up time) 

Ext. voltage reference output 

2.05V ±3%, 1mA max., ~2.6ms (during wake-up time) 

Input sample time after wake-up 

>1.7 ms 

Transmitting indication output (LED) 

3.0V ±3%, 2mA max., 3 x 1.2 ms within 40ms 

 

A change of WAKE pin status forces the onboard controller instantly to check all current 

analog and digital input values. In addition, a user-programmable cyclic wake-up is pro-

vided.  

After wake-up, a radio telegram (input data, unique 32-bit sensor ID, checksum) is trans-

mitted in case of a change of any digital input value compared to the last sending or in case 

of a significant change of measured analog values: >5LSB of AD_1 input, >6LSB of AD_0 

or >14LSB of AD_2. In case of a triggered wake-up a radio telegram is sent in any case. 

In case of no relevant input change, a redundant retransmission is sent after a while to 

announce all current input values. Between the wake-up phases, the module is in sleep 

mode for minimum power consumption. 

 

There is a serial interface which allows to configure several parameters of the module: 

-

 

Threshold values of the AD inputs which lead to immediate radio transmission 

-

 

Manufacturer code (information about manufacturer and type of device) 

 

In  case  a  manufacturer  code  is  programmed  into the module and DI3=0 at wake-up the 

module will transmit a dedicated teach-in telegram containing the manufacturer code.  

 

 

Observe Precautions, electrostatic sensitive devices! 

 

 

Содержание STM110C










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды