manualshive.com logo in svg

EnOcean STM110C, Руководство пользователя

Поделиться
Скачать
EnOcean STM110C Скачать руководство пользователя страница 28

USER MANUAL 

V0.904 

EnOcean GmbH 
Kolpingring 18a 
82041 Oberhaching 
Germany 

Phone +49.89.67 34 689-0 
Fax +49.89.67 

34 

689-50 

[email protected] 
www.enocean.com 

Subject to modifications 
STM110C User Manual V0.904 
February 18, 2008 2:00 PM 
Page 27/40 

 

STM110C 

2.8

 

Serial Data Reception via Transceiver Modules TCM 200C / TCM 210C 

For a detailed description please refer to the User Manual of TCM200C/TCM210C. 
Type of STM110C protocol which is seen at the serial outputs of the receiver modules  

is “4BS” (4 Byte Sensor): 

 
    Description of STM110C radio data content: 

 

ORG 

= 7 dec. always (EnOcean module type “4BS”) 

 

DATA_BYTE3  = Value of AD_2 analog input 

DATA_BYTE2  = Value of AD_1 analog input 

DATA_BYTE1  = Value of AD_0 analog input 

DATA_BYTE0  = Digital sensor inputs as follows: 

 Bit 7                                                       Bit 0 

Reserved 

DI_3  DI_2  DI_1  DI_0 

 

ID_BYTE3 

= module identifier (Byte3) 

ID_BYTE2 

= module identifier (Byte2) 

ID_BYTE1 

= module identifier (Byte1) 

ID_BYTE0 

= module identifier (Byte0) 

 

In case manufacturer ID, device profile and type have been stored in the module the fol-

lowing telegram will be seen on the TCM200C/TCM210C serial interface if DI_3=0: 

 
    Description of STM110C learn telegram: 

 

ORG 

= 7 dec. always (EnOcean module type “4BS”) 

 

DATA_BYTE0..3 see below 

 

 LRN Type = 1 

 

 LRN = 0 

 

 DI0..DI2: current status of digital inputs 

 

 Profile, Type, Manufacturer-ID defined by manufacturer 

ID_BYTE3 

= module identifier (Byte3) 

ID_BYTE2 

= module identifier (Byte2) 

ID_BYTE1 

= module identifier (Byte1) 

ID_BYTE0 

= module identifier (Byte0) 

 

ORG  Data_Byte3  Data_Byte2  Data_Byte1  Data_Byte0  ID 

 

 

 

Profile 

6 Bit 

Type 

7 Bit 

Manufacturer-ID 

11 Bit 

LRN Type 

1Bit 

RE2 

1Bit 

RE1 

1Bit 

RE0 

1Bit 

LRN 

1Bit 

DI2 

1Bit 

DI1 

1Bit 

DI0 

1Bit 

 

With this special learn telegram it is possible to identify the manufacturer of a device and 
the profile and type of a device. There is a list available describing the functionalities of the 
respective products. Please contact EnOcean to receive this list.

Содержание STM110C










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды