manualshive.com logo in svg

EnOcean STM110C, Руководство пользователя

Поделиться
Скачать
EnOcean STM110C Скачать руководство пользователя страница 33

USER MANUAL 

V0.904 

EnOcean GmbH 
Kolpingring 18a 
82041 Oberhaching 
Germany 

Phone +49.89.67 34 689-0 
Fax +49.89.67 

34 

689-50 

[email protected] 
www.enocean.com 

Subject to modifications 
STM110C User Manual V0.904 
February 18, 2008 2:00 PM 
Page 32/40 

 

STM110C 

3.5

 

Solar Cell Handling, Soldering & Mounting 

 
The EnOcean solar cell technology guarantees the highest stabilized efficiency values. At 
the front, the solar modules have a glass covering that protects the photovoltaic layer from 

the effects of the environment and weather. The rear features contacts for the electrical 
connection. 

Handling 

ƒ

 

Prevent injuries due to the sharp glass edges.  

ƒ

 

Always handle the modules carefully, avoid damage of the glass edges that leads to 
glass breakage or glass chips. The layers are sensitive to punctual pressure, scrat-

ching or grinding. During handling and processing, always make sure that no par-
ticles are pushed into the coating. Scratches, imprints or particles pushed into the 
layer can lead to short-circuiting of the module, thus deterioration. 

ƒ

 

The processing of the modules with lacquer spray processes or edge grinding could 

lead to an impairment of the electrical function of the module (electrostatic influ-
ences). 

ƒ

 

In case of necessary module cleaning, the following cleaning agents are suggested: 
Kleenex (200 tissues, Code 7107, D 0261 8930, Kimberly-Clark) / highpure DI- wa-

ter / Ethanol (min. 99,8 Vol.%). 

Soldering 
The solar panel has 3 connection pads on the rear side. On one side you will see the minus 

sign. This is the GND connection.  

 

Apparatus  

ƒ

 

Soldering iron: Temperature-controlled type with 60W heater at least and +/- 5°C 

control range is recommended.  

ƒ

 

Soldering iron tip: Slant type or point type.  

ƒ

 

Temperature Measuring Device: A calibrated contact-type temperature meter (e.g. 

Anritsu Model No. HL-100).  

 

Materials  

ƒ

 

Pb-free solder wire: Sn96.5/Ag3.0/Cu0.5, 

∅

 0.8 mm, (e.g. Kester 245)  

ƒ

 

Lead wire: Dependent on the type of solar cell, use 20 - 30 AWG multi-threads 

stranded type. For Pb-free soldering, the lead wire component shall be complied 

with RoHS requirement. 

 

Procedure for hand soldering  

 

ƒ

 

Environment: Soldering operation shall be performed in a clean environment with 

ventilation to remove soldering fume during the operation. 

ƒ

 

Soldering temperature calibration 

o

 

Temperature measuring device: The device (e.g. Anritsu Model No. HL-100) 

shall be stabilized at room temperature prior to and during calibration.  

o

 

Timing: Calibrate the soldering iron tip before the operation or every 30 

minutes after the soldering. 

o

 

Procedure 

Содержание STM110C










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды