enlighted AirLink GX440 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

enlighted AirLink GX440 Скачать руководство пользователя страница 9

Page 5

Page 6

Page 1

Copyright © 2016 Enlighted Inc. All rights reserved.

All other brand or product names are trademarks of

their respective companies or organizations.

Technical Support

For questions regarding the installation or operation of

this product, contact Enlighted

Technical Support

: [email protected]

Company Contact Information

Location:

930 Benecia Ave, Sunnyvale, CA 94085

Phone:

+1.650.964.1094

Web:

enlightedinc.com

FCC and Industry Canada Compliance Information

This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.

This device complies with Part 15 of the FCC Rules and Industry

Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions:

•

this device may not cause harmful interference, AND

•

this device must accept any interference received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by Enlighted Inc.
could void the user's authority to operate the equipment.

Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:

•

l'appareil ne doit pas produire de brouillage, ET

•

l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.

Figure 1: Plug Load Controller, Locknut, and Sticker

Plug Load Controller

Model PC-01-20

Installation Instructions

Shipped Components

•

Plug load controller (and

½

inch locknut)

•

MAC address sticker

Tools You May Need

•

Wire stripper

Supplies You May Need

•

Wire nuts (or connectors)

•

Junction box (j-box)

•

Two Conductor plus ground 12 AWG solid wire cable

•

Three Conductor plus ground 12 AWG solid wire cable

•

Clamps

93-01142-01 Rev05

Model:

PC-01-20

FCC ID:

AQQ-PC-01-20

IC:

10138A-PC0120

«
...
7
8
9
10
11
...
»

Содержание AirLink GX440





























Отзывы:

Нет отзывов