background image

 

IEEE 802.11b Outdoor 

Wireless Client Bridge

 

 

 

 

User Manual 

 

November 03, 2004 

Version 1.00 

 

 

 
 

Before operating the unit, please read this manual thoroughly, and 
retain it for future reference. 

 

Version 1.02 

  Contents 

CHAPTER 1.

 

INTRODUCTION .................................................................. 1

 

1.1

 

I

NTRODUCING THE 

W

IRELESS CLIENT BRIDGE

........................................... 1

 

1.2

 

P

RODUCT 

F

EATURES

................................................................................. 1

 

1.3

 

P

ACKAGE 

C

ONTENTS

................................................................................. 1

 

1.4

 

S

YSTEM 

R

EQUIREMENTS

........................................................................... 2

 

1.5

 

I

NLINE 

P

OWER 

I

NJECTOR 

(P

O

E) ................................................................ 2

 

CHAPTER 2.

 

INSTALLATION AND BASIC CONFIGURATION ......... 3

 

2.1

 

B

EFORE 

Y

OU 

S

TART

.................................................................................. 3

 

2.2

 

L

OCATE THE 

W

IRELESS CLIENT BRIDGE AND 

I

NLINE 

P

OWER 

I

NJECTOR 

P

ORTS

  4

 

2.3

 

P

REPARING 

I

NSTALLATION

........................................................................ 7

 

2.4

 

B

ASIC 

C

ONFIGURATION

............................................................................. 9

 

2.4.1

 

What you need to know..................................................................... 9

 

2.4.2

 

Basic Configuration Steps ................................................................ 9

 

2.4.3

 

Login into the Web Interface .......................................................... 10

 

2.4.4

 

Set IP Address, Subnet Mask, Default Route IP ............................. 13

 

2.4.5

 

Set Wireless Encryption for Wireless Interface .............................. 14

 

2.4.6

 

Change Supervisor Account & Password ...................................... 15

 

2.4.7

 

Upgrade the Firmware ................................................................... 16

 

2.4.8

 

Back-up the Wireless client bridge’s Configuration Files ............. 20

 

CHAPTER 3.

 

NETWORK TOPOLOGIES ............................................... 22

 

3.1

 

W

IRELESS 

C

LIENT 

B

RIDGE

-

TO

-C

ENTRAL 

W

IRELESS 

B

RIDGE

.................. 23

 

3.2

 

W

IRELESS 

C

LIENT 

R

OUTER

-

TO

-C

ENTRAL 

W

IRELESS 

B

RIDGE

................. 24

 

3.3

 

W

IRELESS 

C

LIENT 

B

RIDGE

-

TO

-C

ENTRAL 

W

IRELESS 

R

OUTER

................. 25

 

3.4

 

W

IRELESS 

C

LIENT 

R

OUTER

-

TO

-C

ENTRAL 

W

IRELESS 

R

OUTER

................ 26

 

CHAPTER 4.

 

NETWORK PARAMETERS .............................................. 28

 

4.1

 

IP

 

C

ONFIGURATION

................................................................................. 28

 

4.2

 

C

ONFIGURE 

SNMP.................................................................................. 28

 

4.2.1

 

Configure Community Pool............................................................ 28

 

4.2.2

 

Configure Trap Host Pool .............................................................. 30

 

4.3

 

C

ONFIGURE 

W

IRELESS RELATED PARAMETERS

....................................... 32

 

4.4

 

U

TILITY

................................................................................................... 35

 

4.4.1

 

Software Upgrade........................................................................... 35

 

4.4.2

 

Administration ................................................................................ 36

 

CHAPTER 5.

 

MONITOR INFORMATION ............................................. 37

 

Содержание EL-2611CB5+




























Отзывы: