EnerWorks EWRA1 Скачать руководство пользователя

Страница: 4 / 38

Contents

1 – Safety
2 – EnerWorks Solar Water Heating Appliance

3 – Site Evaluation

4 – Line-Set Installation

5 – C-Channel Installation

6 – Solar Collector Installation

7 – Collector Flashing and Leaf-Guard Installation

2.1 Description
2.2 Pre-heat Appliance Schematic
2.3 Single Tank Appliance Schematic (USA only)

3.1 Collector Location, Orientation and Shading

tanding Seam M

3.2 Available Roof Space
3.3 Collector Racks
3.4 Line-Set
3.5 Location of Energy Station and Solar Storage Tank

4.1 Line-Set Description
4.2 Line-Set Routing
4.3 Line-Set Installation

5.1 Locating Rafters and Positioning C-Channel
5.2 Securing C-channel Asphalt roof (Shingles)
5.3 Securing C-channel to S

etal Roof

5.4 Roof-Penetration Flashing Boot

6.1 Preparation of Collector(s)

6.2 Hoisting and Securing Collectors to Roof

6.3 Securing Collectors to C-Channel
6.4 Collector Configurations

6.5 Line-Set and Control-Wire Connections

6.1.1 Converting Collector(s) from Left to Right
6.1.2 Installing Temperature Sensor (Thermistor)
6.1.3 Installing Collector Mounting Brackets

6.2.1 Ladder Hoist or Shingle-Lift
6.2.2 Scissor Lift or Articulating or Forklift Boom
6.2.3 Scaffolding
6.2.4 Ladder and Lift Line

6.4.1 One-Collector Configuration
6.4.2 Two-Collector Configuration
6.4.3 Three-Collector Configuration
6.4.4 Four-Collector Configuration

7.1 Side-Flashing for 1-Collector Appliances
7.2 Center-Flashing for 2, 3 and 4-Collector Appliances
7.3 Leaf-Guard Installation

Product and Installation Registration Form
Residential Site Survey
Tool & Supply Checklist

.................................................................................................................................... 3

............................................................................... 4

.......................................................................................................................7

........................................................... 8

............................................................................................................... 8

......................................................................................................... 11

..................................................................................................... 16

..................................................................... 31

..................................................................................................................4

........................................................................5

...............................................................6

................................................................... 7

.................................................................................................... 8

............................................................................................................ 8

...................................................................................................................... 8

..................................................................................................... 8

........................................................................................................... 9

....................................................................................................10

................................................................. 11
................................................................. 13

........................................................ 15

................................................................................... 15

.......................................................................................... 16

...................................................................................... 23

.................................................................................... 26

................................................................................... 27

................................................................... 17

............................................................... 20

...................................................................... 21
...................................................................... 22

................................................................... 23

............................................................................................................. 23

.................................................................................................. 24

................................................................................ 25

................................................................................... 26

................................................................................... 27

.................................................................................... 28

......................................................................... 29
......................................................................... 30

...................................................... 31

................................................................................................ 33

..................................................................................... 34

................................................................................................................. 35

.................................................................................................................. 36

Module 4

Solar Collector

Installation Manual

Содержание EWRA1







































Результаты поиска

Содержание EWRA1

Отзывы:

Похожие инструкции для EWRA1

Бренды по названию

Популярные бренды

EnerWorks EWRA1, Руководство по установке

Результаты поиска

Содержание EWRA1

Отзывы:

Похожие инструкции для EWRA1

Бренды по названию

Популярные бренды