EnerWorks EWRA1 страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 38

background image

Solar Collector

Installation Manual

EnerWorks encourages installers of EnerWorks products to always keep workmanship, best practices
and safety in mind. An organized installation will benefit both installer and end-user.

The EnerWorks Solar Collector is one of the highest-rated in North America. This assessment was
carried out by third-party testing under the supervision and scrutiny of the Solar Rating & Certification
Corporation™ (SRCC™). The EnerWorks Heat Safe Solar Collector has SRCC™ OG-100 certification
(Certification #: 100-2005-014A) and the EnerWorks Residential Solar Water Heating Appliances are
certified to OG-300 standards. This certification does not imply endorsement or warranty of these
products by the SRCC™.

The Pre-Heat and Single Tank Appliances described in this manual, when properly installed and
maintained, meet or exceed the standards established by the Florida Solar Energy Center (FSEC), in
accordance with Section 377.705, Florida Statutes. This certification does not imply endorsement or
warranty of this product by the Florida Solar Energy Center or the State of Florida.

The EnerWorks Pre-Heat Appliance is the first system in North America to achieve the Canadian
Standards Association (CSA) certification (CSA F379.1). This certification does not imply endorsement
or warranty by CSA.

Foreword

Recognize this symbol as an indication of important safety information!

EnerWorks Residential Solar Water Heating Appliances must be installed as
directed by this manual by an EnerWorks-authorized dealer or warranty is void.

CALIFORNIA PROPOSITION 65 WARNING: This product contains
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.

Appliance must only be installed by an EnerWorks-authorized
dealer or warranty is void.

«
1
2
3
4
...
»

Содержание EWRA1







































Отзывы:

Нет отзывов

Похожие инструкции для EWRA1

Бренд: Gardena Страницы: 11

Бренд: Wanner Engineering Страницы: 16

Бренд: Eaton Страницы: 68

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 16

Standard Series

Бренд: Facilities Resource Group Страницы: 61

Бренд: Ibiza Страницы: 24

Бренд: i3-TECHNOLOGIES Страницы: 19

Бренд: salmson Страницы: 12

Бренд: ICP DAS USA Страницы: 4

Бренд: Navien Страницы: 48

Бренд: Navien Страницы: 2

Бренд: Vectaire Страницы: 2

Бренд: Davey Страницы: 28

Бренд: RainSoft Страницы: 16

Бренд: Rafiki Protection Страницы: 32

Бренд: 3M Страницы: 44

Бренд: Xylem Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды