background image

5 – C-Channel Installation

Do  not  perform  roof  work  when  strong  winds,  rain,  thunderstorms  or  lightning  are  active  or 
expected.

In  the  interest  of  safety  and  an  efficient  installation  process,  assemble  all  necessary  tools  and 
components for roof C-channel and collector installation. See Appendix - Tool and Supply Checklist.

TIP: C-channel twirl-nuts (for securing collectors to C-channel) are equipped with springs that hold 
them in place. Push twirl-nuts through C-channel and turn 90° clockwise to secure them. Position 
them at approximate collector mounting points, at center and at ends, before hoisting C-channel to  
roof; fewer pieces to carry – fewer pieces to drop!

After  roof-penetration  has  been  made  and  approximate  location  of  solar  collectors  has  been 
determined:

1.  Determine location and spacing of roof rafters (Fig. 5.1.1). This may be easy from inside attic, but     
     rafter positions need to be transferred to exterior roof. This may be done in a number of ways and    
     will depend on access:

• Measure from side edge of roof or carefully remove 

soffits to determine spacing.

• Temporary metal clips, strips or pipe may be fixed to 

the  rafters  inside  the  attic  and  a  metal 
detector (eg., Zircon MT6, Bosch D-Tect 100) used to 
determine rafter location from outside.

• Using  roof-penetration  as  landmark,  distance  to 

rafters  may  be  measured  inside  attic  and 
measurements transferred to exterior.

• A nail may be used, pushed through from inside, to 

m a r k   l o c a t i o n   o f   r a f t e r .   A n y   r o o f -
penetrations must be appropriately sealed. 

Rafters are often not exactly parallel and spacing at eaves may not be equivalent to spacing where C-channel is 
to be installed.

EnerWorks is not responsible for any damage to structural member due to inadequate anchoring  and sealing 
of C-channel and of solar collectors. Assure to meet any applicable code

5.1 Locating Rafters and Positioning C-Channel

Fig. 5.1.1 – Roof rafter spacing.

Solar Collector
Installation Manual

11

Module 4

Содержание EWRA1







































Отзывы: