Overview Guide
Contents:
Installation…………………………...….. 1-2
LED Indicators….……………….....…… 3-5
Home Screens……..……….…..……....
5-7
Soft Keys……….……………..…..…….. 7-15
Hot Keys…….……………..…….…….. 16-19
Replay Function (OPTICS RE)………… 20
Specifications……..……….…..…………
22
IMPORTANT
Signal degradation can result if cable is run in conduit with AC wiring or in other electrically “noisy” environments; these can affect
the maximum length the cable can run without incurring transmission errors.
CAUTION: EQUIPMENT DAMAGE
The MATE3s is intended for indoor installations only.
NOTES
The MATE3s voltage is less than 30 Vdc and is thus considered a “limited energy” circuit normally requiring no conduit.
CAT5 cable is not as strong as house wiring and must be handled carefully. Avoid kinking the cable or tearing its outer sheathing.
Use plastic standoff cable staples, J-hooks, or cable trays to support long runs of CAT5 cable.
Do not splice cables.
IMPORTANT:
Not intended for use with
life support equipment.
7 1/8"
(17.9 cm)
2 3/8"
(6.0 cm)
7 ¼” (18.4 cm)
6 5/8" (16.8 cm)
5/16" (0.79 cm)
9/16"
(1.4 cm)
1 5/8" (4.2 cm)
7 1/2” (19 cm)
!
F
F
E
F
A
B
C
D
G
F
F
F
F
F
D
H
Features
A
: LCD display screen
E
: Navigation keys
B
: Soft keys
F
: Mounting Holes
C
: Hot keys
G
: Ethernet port
D
: SD card slot
H
: HUB Communications Manager port
NOTE
: This document assumes knowledge of features, functions, and operation
of other OutBack products. Consult appropriate literature as necessary.
Items
1
,
2
, and
3
are the MATE3s
mounting options from OutBack.
Item
4
is a semi-transparent front view which
also shows the ports and other back features.
To mount the MATE3s on the wall
without the accessory brackets:
1. Cut a hole in the surface at the location and
size shown in
4
. This allows room for the
CAT5 cables to protrude through the wall.
2. Place the MATE3s on the wall with the cables
inside the hole. Mark the mounting holes (
F
)
by pushing a long nail into the mounting holes
and putting a leader hole in the wall surface.
NOTE
:
Do not use a nail that is larger than
the mounting screws.
1
⅝
"
(4.1 cm)
2"
(5.1 cm)
1 ½"
(3.8 cm)
1
⅜
" (3.5
cm)
F
F
F
F
1
2
3
4
Contact Information
About OutBack Power
OutBack Power is a leader in advanced energy conversion technology. OutBack products include true sine wave inverter/chargers,
maximum power point tracking charge controllers, and system communication components, as well as circuit breakers, batteries,
accessories, and assembled systems.
Contact Information
Mailing Address:
17825 – 59th Avenue NE
Suite B
Arlington, WA 98223 USA
Web Site:
www.outbackpower.com
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, OUTBACK POWER:
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER
INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT, CONSEQUENTIAL
OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION
WILL BE ENTIRELY AT THE USER’S RISK.
OutBack Power cannot be responsible for system failure, damages, or injury resulting from improper installation of their products.
Notice of Copyright
MATE3s System Display and Controller Overview Guid
e © 2017 by OutBack Power. All Rights Reserved.
Trademarks
OutBack Power, the OutBack Power logo, OPTICS RE, and Grid/Hybrid are trademarks owned and used by
OutBack Power, an EnerSys company. These trademarks may be registered in the United States and other countries.
Date and Revision
November
2019, Revision B
Part Number
900-0124-01-02 Rev B
