background image

7

1

2

3

5

6 7

9

8

10

11

12

13

14

4

Figure 1, Features and Components

Key:

1.  Safety Guard
2.  Piston and Moving Blade
3.  Lifting Eyebolt
4.  Safety Guard Latch
5.  Trigger On-Off Switch
6.  Oil Reservoir
7. Grip/Handle

8.  AC Power Cord
9.  Electric Motor
10. Directional Lever
11. Hydraulic Cylinder
12. Cutting Head
13. Fixed Blade
14. Storage Case

3.0   CONFORMANCE TO NATIONAL AND 

INTERNATIONAL STANDARDS

Enerpac declares that this product has been 

tested and conforms to applicable standards 

and is compatible with all CE requirements. 

A copy of an EU Declaration of Conformity is 

enclosed with each shipment of this product.

4.0  DESCRIPTION

The Enerpac model ECCE32 is a fixed-head hydraulic 

cutter designed to cut metal chains.
The cutter contains two blades, one fixed and one 

moving. The moving blade is actuated by a hydraulic 

cylinder.
Hydraulic force is provided by an AC powered electric 

motor and an internal hydraulic pump. The pump 

provides oil flow to the hydraulic cylinder, which 

advances the cylinder piston and moving blade.
A hydraulic reservoir with built-in rubber diaphragm 

provides a constant supply of oil to the pump, regardless 

of tool orientation or the amount of piston extension.

A trigger style on-off switch, mounted on the cutter grip, 

starts and stops the electric motor. The trigger must 

remain pressed during the cutting process.
See Figure 1 for a description of cutter major features and 

components. Refer to Sections 2.1 through 2.4 of this 

manual for maximum cutting capacities, specifications 

and dimensions.

5.0  RECEIVING INSTRUCTIONS

Visually inspect all components for shipping damage. 

Shipping damage is not covered by warranty. If shipping 

damage is found, notify carrier at once. The carrier is 

responsible for all repair and replacement costs resulting 

from damage in shipment.

Содержание ECCE32

























Отзывы: