Energic Plus TST-D Скачать руководство пользователя страница 16

Страница: 16 / 19

MAINTENANCE

The MAINTENANCE function is useful to keep the battery in perfect condition when it’s not

used for an indefined time (weeks, months, . . .) .

It is sufficient to leave the battery connected to the charger: the control board will keep the

battery voltage under control and will activate the charger automatically when the voltage falls

below a predefined minimum threshold .

While the charger is off and the battery voltage is being monitored, this message is displayed:

If the voltage falls below the minimum threshold, the charger will give a refresh charge to pull up the

voltage to a programmed maximum threshold, and the display will show the message:

“F2” .

NOTE

With this “voltage controlled” maintenance/refresh system, the battery will be kept in perfect con-

dition for an undefined time, without any risk of undercharge or overcharge.

If the battery is in ideal condition (no self-discharge) the refresh charge will never be activated.

If the battery is in bad condition (self-discharge is significant), the refresh charge will be often acti-

vated and the battery will be kept charged without problems.

Содержание TST-D



















