Getting
FR
IE
Getting
started...
08
09
GB
IE
GB
IE
Getting started...
Getting started...
ENB520GRB by
Energer
ENB520GRB by
Energer
Technical and legal
information
Technical and legal
information
General safety
Additional safety
11 Do not abuse the cord
> Never yank the cord to disconnect it from the socket.
> Keep the cord away from heat, oil and sharp edges.
12 Secure work
> Where possible use clamps or a vice to hold the work.
> It is safer than using your hand.
13 Do not over reach
> Keep proper footing and balance at all times.
14 Maintain tools with care
> Keep cutting tools sharp and clean for better and safer performance.
> Follow instruction for lubricating and changing accessories. Inspect tool cords
periodically and if damaged have them repaired by an authorized service facility.
Inspect extension cords periodically and replace if damaged. Keep handles dry,
clean and free from oil and grease.
15 Disconnect tools
> When not in use, before servicing and when changing accessories such as
blades, bits and cutters, disconnect tools from the power supply.
16 Remove adjusting keys and wrenches
> Form the habit of checking to see that keys and adjusting wrenches are removed
from the tool before turning it on.
17 Avoid unintentional starting
> Ensure switch is in "off" position when plugging in.
18 Use outdoor extension leads
> When the tool is used outdoors, use only extension cords intended for outdoor
use and so marked.
19 Stay alert
> Watch what you are doing, use common sense and do not operate the tool when
you are tired.
20 Check damaged parts
> Before further use of tool, it should be carefully checked to determine that it will
operate properly and perform its intended function.
> Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation.
> A guard or other part that is damaged should be properly repaired or replaced by
an authorised service centre unless otherwise indicated in this instruction
manual.
> Have defective switches replaced by an authorised service centre.
> Do not use the tool if the switch does not turn it on and off.
21 Warning
> The use of any accessory or attachment other than one recommended in this
instruction manual may present a risk of personal injury.
22 Have your tool repaired by a qualified person
> This electric tool complies with the relevant safety rules. Repairs should only be
carried out by qualified persons using original spare parts, otherwise this may
result in considerable danger to the user.
> Never drape the power cable over the machine bench.
> The machine is to be used only for its prescribed purpose.
> Wear protective clothing. Wear full face protection, eye protection or safety
goggles, in accordance with the job at hand. Where appropriate, wear a dust
mask, ear defenders, protective gloves or special aprons that keep grinding and
material particles away from you.
Protect your eyes from the foreign bodies that fly off during certain applications.
Dust or breathing masks must be used to filter particles generated by the
application.
Hearing loss can be caused by exposure to high intensity noise.
> Always wear a dust mask and safety goggles.
Contact with or breathing in noxious / toxic dust produced by grinding metal that is
finished with lead paint can be dangerous for the user and surrounding people.
> This power tool must not be used for wet grinding. Use for dry grinding only.
Coolant can weaken the bonding strength of the wheel and cause it to fail.
> This bench grinder should only be used when stationary. Secure to a solid, even
surface.
> Do not use any accessories that have not been especially designed and
recommended for this power tool by the manufacturer. Simply because an
accessory can be connected to your power tool does not guarantee it can be used
safely.
> Only use grinding disks whose diameter, thickness and intended use meet the
equirements of this power tool. Incorrectly sized grinding disks may not be
sufficiently screened or controllable. Use of unsuitable grinding disks can result in
danger to the user or damage to the power tool.
> Never touch the spinning grinding disks! Make sure the grinding disks have come
to a complete standstill after turning off before you touch them.
> When you have checked the tool attachment and have attached it, make sure you
and others nearby keep away from the area of the rotating tool attachment and let
the appliance run at the maximum speed for a minute. Most damaged tool
attachments will break off in this test period.
> Make sure bystanders are a safe distance from your work area. Anyone entering
the work area must wear personal protective clothing. Pieces may break off the
work piece or sparks may fly off and can also cause injuries outside the direct
work area.
> Position the power cable clear of the spinning tool attachment. If you lose control
of the appliance,the power cable can be severed or tangled and your hands or
arms may get caught in the spinning tool attachment.
> Do not leave the power tool running when you are not using it. Your clothing can
become entangled when it comes into contact with the spinning tool attachment,
causing the tool attachment to drill into your body.
> Clean the power tool’s air vents regularly. The motor’s fan draws dust into the
housing and the heavy build-up of metal dust can result in electrical hazards.
> Do not use the power tool in the vicinity of flammable materials. Sparks may
cause these materials to ignite.
