manualshive.com logo in svg

Enerdrive ePro Plus, Руководство пользователя

Поделиться
Скачать
Enerdrive ePro Plus Скачать руководство пользователя страница 9

www.enerdrive.com.au

Page 9

2.  QUICKSTART

2.1 General

This chapter describes the minimum amount of steps that need to be followed in order to 
get your ePRO Plus up and running. It assumes that the enclosed installation guide has been 
followed carefully and that the ePRO Plus is powered up for the  rst time. After this the Setup 
wizard will start automatically. If the Setup wizard does not start and the ePRO Plus will jump to 
the normal operating mode after power up, it has already been con gured before. In that case 
you can choose to restore the factory default settings (see chapter 7, for more information) and 
start from the beginning. Please see the next chapter for more details about the Setup wizard.

2.2 Setup wizard

The Setup wizard will guide you through a few basic steps that are essential for a correctly 
functioning ePRO Plus. No other Function settings can be accessed before the Setup wizard 
has been completed.

Step 1-2: Main battery type

The display will start by showing the battery type selection screen. You can use the left (<) and 
right (>) arrow keys to select between AGM (default), GEL, Flooded and Lithium LiFePO4. Please 
consult your battery manual or supplier, to  nd out the correct type of your battery system. Once 
the selection has been made, press the MENU   key to jump to the next step.

Step 2-2: Main battery capacity

The default battery capacity value is 200Ah. This can be changed by pressing the left or right 
arrow keys until the desired value is reached. The standard battery capacity value is based on 
a discharge rate of 20 hours. When your battery capacity is rated at a di erent discharge rate, 

Содержание ePro Plus













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды