background image

Solitrend MMP60

Commissioning

Hauser

15

CK

 mode (Cyclic with Boost Filter)

For complex applications in mixers and dryers

CC

 mode (Cyclic Cumulated)

With automatic totalization of moisture quantity measurements in one batch process if no

PLC controller is used

CH

 mode (Cyclic Hold)

Standard operating mode for applications in the construction industry. Similar to the 

CC

mode, but with filtering and without totalization. The 

CH

 mode is ideal for very short batch

times down to 2 s if the sensor has been installed under the silo discharge hatch. The 

CH

mode performs filtering automatically. This allows drip water that forms in the silo to be

filtered out of the measured value, for example.

8.3  

Calibration curve set A for general bulk solids applications

The devices are supplied with a suitable calibration. A maximum of 15 different calibrations

can be saved in the device and can be activated and adjusted via the remote display. To pre-

test the compatibility of a calibration curve, the user can select individual calibration curves

(Cal.1 to Cal.15) in the 

Material cal.

 menu item, test the curve with the material to be

measured and activate it. The desired calibration curve - which may have been modified - is

active once the operating voltage is switched on.

Содержание Solitrend MMP60





















Отзывы: