Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 207

Страница: 207 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

207

Puls.outp.sim. 1 to n



Navigation

 Expert → Diagnostics → Simulation → Puls.outp.sim. 1 to n (0458–1 to n)

Prerequisite

In the

Operating mode

parameter (→  120), the

Pulse

option is selected.

Description

Use this function to switch simulation of the pulse output on and off. The display

alternates between the measured value and a diagnostic message of the "Function check"

category (C) while simulation is in progress.

Selection

• Off

• Fixed value

• Down-count. val.

Factory setting

Off

Additional information

Description

The desired simulation value is defined in the

Pulse value 1 to n

parameter.

Selection

• Off

Pulse simulation is switched off. The device is in normal measuring mode or another

process variable is being simulated.

• Fixed value

Pulses are continuously output with the pulse width specified in the

Pulse width

parameter (→  123).

• Down-count. val.

The pulses specified in the

Pulse value

parameter (→  207) are output.

Pulse value 1 to n



Navigation

 Expert → Diagnostics → Simulation → Pulse value 1 to n (0459–1 to n)

Prerequisite

In the

Puls.outp.sim. 1 to n

parameter, the

Down-count. val.

option is selected.

Description

Use this function to enter a pulse value for the simulation. In this way, users can verify the

correct adjustment of the pulse output and the correct function of downstream switching

units.

User entry

0 to 65

535

Switch sim. 1 to n



Navigation

 Expert → Diagnostics → Simulation → Switch sim. 1 to n (0462–1 to n)

Prerequisite

In the

Operating mode

parameter (→  120), the

Switch

option is selected.

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды