Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 101

Страница: 101 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

101

Additional information

Current input behavior

The current input behaves differently depending on the settings configured in the

following parameters:

• Current span (→  100)

• Failure mode (→  101)

Configuration examples

Pay attention to the configuration examples for

4 mA value

parameter (→  108).

20 mA value



Navigation

 Expert → Input → Current input 1 to n → 20 mA value (1607–1 to n)

Description

Use this function to enter a value for the 20 mA current.

User entry

Signed floating-point number

Factory setting

Depends on country and nominal diameter

Additional information

Configuration examples

Pay attention to the configuration examples for

4 mA value

parameter (→  108).

Failure mode



Navigation

 Expert → Input → Current input 1 to n → Failure mode (1601–1 to n)

Description

Use this function to select the input behavior when measuring a current outside the

configured

Current span

parameter (→  100).

Selection

• Alarm

• Last valid value

• Defined value

Factory setting

Alarm

Additional information

Options

• Alarm

An error message is set.

• Last valid value

The last valid measured value is used.

• Defined value

A user-defined measured value is used (

Failure value

parameter (→  102)).

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды