Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 102

Страница: 102 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

102

Hauser

Failure value



Navigation

 Expert → Input → Current input 1 to n → Failure value (1602–1 to n)

Prerequisite

In the

Failure mode

parameter (→  101), the

Defined value

option is selected.

Description

Use this function to enter the value that the device uses if it does not receive an input

signal from the external device, or if the input signal is invalid.

User entry

Signed floating-point number

Factory setting

3.4.2

"Status input 1 to n" submenu

Navigation

 Expert → Input → Status input 1 to n

‣

Status input 1 to n

Terminal no. (1358–1 to n)

→  102

Assign stat.inp. (1352–1 to n)

→  103

Val.stat.inp. (1353–1 to n)

→  103

Active level (1351–1 to n)

→  104

Response time (1354–1 to n)

→  104

Terminal no.

Navigation

 Expert → Input → Status input 1 to n → Terminal no. (1358–1 to n)

Description

Displays the terminal numbers used by the status input module.

User interface

• Not used

• 24-25 (I/O 2)

• 22-23 (I/O 3)

Additional information

"Not used" option

The status input module does not use any terminal numbers.

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды