Endress+Hauser Nivotester FTR525 Скачать руководство пользователя страница 30

Страница: 30 / 68

Nivotester FTR525

Hauser

Commissioning

038

2 1 13

3
4

19 Manual adjustment upper limit (UL)
1 Current measured value

2 Set detection range (= 0-100% of signal output)

3 Percentage value for the upper limit relative to the maximum possible detection range

4 Upper limit (adjustable using this function)

8�4�1�4 Level limit detection damping

Application

2000

→

Sensor

2100

→

Limit detection

2110

→

Damping

2114

It is possible, for instance in the case of very turbulent processes, to steady the measuring

signal. To do so, a time can be set over which the measured values are averaged.

Options: 100 ms to 20 s, Off

Setting the damping results in a longer reaction time.

8�4�1�5 Automatic setup of motion detection

Application

2000

→

Sensor

2100

→

Motion detection

2120

→

Automatic setup

2121

Automatic setup is carried out with movement of bulk solids either present or not

present (in front of the FDR57 transceiver); the option selected for this corresponds to the

state of the bulk flow.

Options: "With movement", "Without movement"

1 2

FQR57 FDR57

20 Setup conditions of the motion detection

The following manual adjustment functions can be used to carry out fine adjustment of

the microwave barrier or to suit changing application conditions.

8.4.1.6 Manual adjustment lower limit (LL) motion detection

Application

2000

→

Sensor

2100

→

Motion detection

2120

→

Manual adjustment LL

2122

This function can be used to change the lower limit of the set detection range of the

motion detection (function

2112

→ 28).

Содержание Nivotester FTR525





































































Результаты поиска

Содержание Nivotester FTR525

Отзывы:

Endress+Hauser Nivotester FTR525, Руководство по эксплуатации, Страница: 30 / 68

Результаты поиска

Содержание Nivotester FTR525

Отзывы: