Endress+Hauser MODBUS RS485 Скачать руководство пользователя страница 56

Страница: 56 / 92

Operation

LPGmass Modbus RS485

Hauser

Navigation

"Diagnostics" menu → Measured values → Totalizer

‣

Totalizer

Totalizer value 1 to n

→  56

Totalizer overflow 1 to n

→  56

Parameter overview with brief description

Parameter

Prerequisite

Description

User interface

Totalizer value

One of the following options is selected
in the

Assign process variable

parameter (→  51)

Totalizer 1 to n

submenu:
• Volume flow
• Mass flow
• Corrected volume flow

Displays the current totalizer counter
value.

Signed floating-point
number

Totalizer overflow

One of the following options is selected
in the

Assign process variable

parameter (→  51)

Totalizer 1 to n

submenu:
• Volume flow
• Mass flow
• Corrected volume flow

Displays the current totalizer overflow.

Integer with sign

11.4 Adapting the measuring device to the process

conditions

The following are available for this purpose:

• Basic settings using the

Setup

menu (→  40)

• Advanced settings using the

Advanced setup

submenu (→  48)

11.5 Performing a totalizer reset

The totalizers are reset in the

Operation

submenu:

• Control Totalizer

• Reset all totalizers

Navigation

"Operation" menu → Totalizer handling

‣

Totalizer handling

Control Totalizer 1 to n

→  57

Preset value 1 to n

→  57

Reset all totalizers

→  57

Содержание MODBUS RS485





























































































Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser MODBUS RS485, Руководство по эксплуатации

Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды