Endress+Hauser Liquiline System CA80TP Скачать руководство пользователя страница 9

Страница: 9 / 48

Liquiline System CA80TP

Incoming acceptance and product identification

Hauser

Incoming acceptance and product identification

3.1

Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify your supplier of any damage to the packaging.

Keep the damaged packaging until the matter has been settled.

2. Verify that the contents are undamaged.

 Notify your supplier of any damage to the delivery contents.

Keep the damaged products until the matter has been settled.

3. Check the delivery for completeness.

 Check it against the delivery papers and your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.
 The original packaging offers the best protection.

The permitted ambient conditions must be observed (see "Technical data").

If you have any questions, please contact your supplier or your local sales center.

NOTICE

Incorrect transportation can damage the analyzer

‣

Always use a lifting truck or a fork-lift to transport the analyzer.

3.2

Product identification

3.2.1

Nameplate

Nameplates can be found:

• On the inside of the door on the bottom right, or on the front in the bottom right-hand

corner

• On the packaging (adhesive label, portrait format)
The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Extended order code

• Serial number

• Firmware version

• Ambient and process conditions

• Input and output values

• Measuring range

• Activation codes

• Safety information and warnings

• Certificate information

• Approvals as per version ordered

‣

Compare the data on the nameplate with your order.

Содержание Liquiline System CA80TP

















































Результаты поиска

Содержание Liquiline System CA80TP

Отзывы:

Похожие инструкции для Liquiline System CA80TP

Бренды по названию

Популярные бренды

Endress+Hauser Liquiline System CA80TP, Краткое руководство по эксплуатации

Результаты поиска

Содержание Liquiline System CA80TP

Отзывы:

Похожие инструкции для Liquiline System CA80TP

Бренды по названию

Популярные бренды