Endress+Hauser Liquiline System CA80TP Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 48

background image

Electrical connection

Liquiline System CA80TP

34

Hauser

Individual types of protection permitted for this product (impermeability (IP), electrical safety,

EMC interference immunity, Ex protection) can no longer be guaranteed if, for example:

• Covers are left off.

• Different power units to the ones supplied are used.

• Cable glands are not sufficiently tightened (must be tightened with 2 Nm for the confirmed

level of IP protection).

• Modules are not fully secured.

• The display is not fully secured (risk of moisture entering due to inadequate sealing).

• Loose or insufficiently tightened cables/cable ends.

• Conductive cable strands are left in the device.

5.5

Post-connection check

L

WARNING

Connection errors

The safety of people and of the measuring point is under threat. The manufacturer does not

accept any responsibility for errors that result from failure to comply with the instructions in

this manual.

‣

Operate the device only if you can answer

yes

to

all

of the following questions.

Instrument status and specifications

‣

Is there any external damage to the device and cables?

Electrical connection

‣

Are the mounted cables strain-relieved?

‣

Have the cables been routed without loops and cross-overs?

‣

Have the signal lines been connected correctly in accordance with the wiring diagram?

‣

Are all plug-in terminals securely engaged?

‣

Are all the connection wires securely positioned in the cable terminals?

«
...
32
33
34
35
36
...
»

Содержание Liquiline System CA80TP

















































Отзывы:

Нет отзывов

Похожие инструкции для Liquiline System CA80TP

Бренд: QLA Страницы: 18

Бренд: Bamo Страницы: 8

Бренд: Oldham Страницы: 22

Бренд: Saimo Страницы: 101

Бренд: Omano Страницы: 14

Бренд: Unior Страницы: 2

Бренд: Vaisala Страницы: 83

Бренд: Shimpo Страницы: 68

Бренд: Xsensor Страницы: 13

Бренд: RAM Страницы: 43

Бренд: ScienTECH Страницы: 43

Бренд: EIJKELKAMP Страницы: 11

Бренд: SMPE Страницы: 2

Бренд: T Scale Страницы: 64

Бренд: M-system Страницы: 5

Бренд: P3 International Страницы: 12

Бренд: Hanna Instruments Страницы: 24

Бренд: Danfoss Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды