Endress+Hauser iTHERM TrustSens TM371 Скачать руководство пользователя страница 94

Страница: 94 / 106

Operating menu and parameter description

iTHERM TrustSens TM371, TM372

Hauser

14.4.1 "System" submenu

Unit →  78

Navigation

Setup → Unit

Expert → System → Unit

Damping

Navigation

Expert → System → Damping

Description

Use this function to set the time constant for current output damping.

User entry

0 to 120 s

Factory setting

0 s

Additional information

The current output reacts with an exponential delay to fluctuations in the measured value.

The time constant of this delay is specified by this parameter. If a low time constant is

entered, the current output follows the measured value quickly. On the other hand, if a

high time constant is entered, the current output reaction is delayed.

"Administration" submenu

Define device write protection code

Navigation

Expert → System → Administration → Define device write protection code

Description

Sets a write protection code for the device.

If the code is programmed into the device firmware it is saved in the device and the

operating tool displays the value

so that the defined write protection code is not

openly displayed.

User entry

0 to 9

999

Factory setting

If the device is delivered with this factory setting the device write protection is not

active.

Содержание iTHERM TrustSens TM371











































































































Результаты поиска

Содержание iTHERM TrustSens TM371

Отзывы:

Бренды по названию

Популярные бренды

Endress+Hauser iTHERM TrustSens TM371, Руководство по эксплуатации

Результаты поиска

Содержание iTHERM TrustSens TM371

Отзывы:

Бренды по названию

Популярные бренды