Encoder TB-544 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 10

background image

1-800-366-5412 | www.encoder.com | [email protected]

Page 5/10

TB-544

LCX DRAW WIRE INSTALLATION GUIDE

© 2020 Encoder Products Company TB-544, REV. 11/12/2020

STEP 3
By tightening the inner radial screw (approx. 2 Nm / 283 oz-in) with a 2.5 mm hex driver the encoder shaft will be clamped to the draw wire
unit and is secured from slipping.

STEP 4
By tightening the outer radial screw (approx. 2 Nm / 283 oz-in) with a 2.5 mm hex driver the encoder housing will be clamped to the draw wire
housing and is secured from twisting. The complete assembly is now ready to be mounted at the desired location.

«
...
3
4
5
6
7
...
»

Содержание TB-544











Отзывы:

Нет отзывов

Похожие инструкции для TB-544

Бренд: Samson Страницы: 28

Бренд: Konig Страницы: 30

Бренд: K&S BASIC Страницы: 17

Бренд: Radyne ComStream Страницы: 156

Бренд: Sungrow Страницы: 138

Бренд: Transition Networks Страницы: 2

Varispeed-606PC3

Бренд: YASKAWA Страницы: 157

Бренд: Icy Box Страницы: 30

Бренд: Millennia Страницы: 2

Бренд: Daewoo Страницы: 16

Бренд: ADF Web Страницы: 29

Бренд: Wentronic Страницы: 4

BrightSign MH6-HD

Бренд: Audio Authority Страницы: 8

Бренд: Sollae Systems Страницы: 70

Бренд: Wolverine Страницы: 14

Multi-Decoder MD-2

Бренд: tams elektronik Страницы: 40

Бренд: Tektronix Страницы: 41

Бренд: Audiophony PA Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды