background image

 

LP11002 Hardware Installation Manual

Page 8

FCC and Regulatory Notices

LP11002 HBA Models

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.

Note:This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own expense. The reader is cautioned that 
changes or modifications made to the equipment not expressly approved by Emulex could void the 
user's authority to operate this equipment. The above statement applies to products marketed in the 
USA.

This class A digital apparatus meets all requirements of the Industry Canada (IC) Interference - Causing 
Equipment Standard (ICES-003).

Cet appareil numerique de la Classe A respecte toutes les exigences du reglement sur le materiel 
brouilleur du Canada. This statement applies to products marketed in Canada.

Notice for Japan and Translations (VCCI)

Product Label

This is a Class A product. In a domestic environment this product may cause radio interference in which 
case the user may be required to take adequate measures. VCCI—A

 

Manual Notice

Translation:

This is a Class A product based on the standard of the Voluntary Control Council for Interference by 
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio 
disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. 

 

Responsible Party:

Paul Folino, Chief Executive Officer

Emulex Corporation (714) 662-5600

3333 Susan St. Costa Mesa, CA. 92626 USA

Содержание LP11002

















Отзывы: