Empire SR-10TBC-3 Скачать руководство пользователя страница 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

UNVENTED 

ROOM HEATER

MODELS

SR-10TBC-3      SR-18TBC-3

SR-18T SHOWN

This is an unvented gas-fired heater.  It uses air (oxy

-

gen) from the room in which it is installed.  Provisions 

for adequate combustion and ventilation air must be 

provided. Refer to page 6.

WARNING: If not installed, operated and maintained 

in accordance with the manufacturer’s instructions, 

this product could expose you to substances in fuel 

or from fuel combustion which can cause death or 

serious illness.

Unvented room heaters are for installation in SINGLE 

FAMILY TYPE RESIDENCES ONLY,  and the installation 

is limited to ONE (1) unit per residence.

Unvented  room  heaters  are  NOT  TO  BE  USED  IN 

BEDROOMS, MOBILE HOMES, TRAILERS AND REC

-

REATIONAL VEHICLES.

Unvented room heaters are only to be used as supple

-

mentary heat and NOT AS PRINCIPAL SOURCE OF 

HEAT for the room in which the unit is installed.

Unvented  room  heaters  are  not  for  installation  in 

rooms having space which shall limit the appliance 

input to a maximum of “20 BTUH” per cubic foot of 

room space.

Unvented room heaters are NOT FOR COMMERCIAL 

OR INDUSTRIAL USE.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM 

HEATERS

Water  vapor  is  a  by-product  of  gas  combustion. An 

unvented room heater produces approximately one (1) 

ounce (30ml) of water for every 1,000 BTU’s (.3KW’s) 

of gas input per hour. Refer to page 6.

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

—  WHAT TO DO IF YOU SMELL GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

 

•  Immediately  call  your  gas  supplier  from  a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation and service must be performed by a 

qualified installer, service agency or the gas sup

-

plier.

WARNING: If the information in these instructions 

are  not  followed  exactly,  a  fire  or  explosion  may 

result causing property damage, personal injury or 

loss of life.

Page 1

Содержание SR-10TBC-3

























Отзывы: