manualshive.com logo in svg

Empire Comfort Systems VFSUE18-1, Инструкция по установке и руководство пользователя

Поделиться
Скачать
Empire Comfort Systems VFSUE18-1 Скачать руководство пользователя страница 2

31722-1-1213

Page 2

SecTION  

PAGe

CARTON CONTENTS .................................................................................................................... 5
HARDWARE PACKAGE................................................................................................................. 5
IMPORTANT SAFETY INFORMATION .......................................................................................... 6
SAFETY INFORMATION FOR USERS OF LP-GAS ..................................................................... 7
INTRODUCTION ............................................................................................................................ 8
GENERAL INFORMATION............................................................................................................. 9
REQUIREMENTS FOR CANADA ................................................................................................ 10
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS ...................................... 11
PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR ...................................... 11
CLEARANCES ........................................................................................................................12-13
COMBUSTIBLE MATERIAL ......................................................................................................... 14
FIREPLACE PREPARATION ....................................................................................................... 14
PLACEMENT OF VFSUE CONTROL MODULE .......................................................................... 15
INSTALLING AS A VENTED APPLIANCE .................................................................................... 16
MOUNTING INTO A FIREPLACE OR FIREBOX ......................................................................... 16
GAS SUPPLY ............................................................................................................................... 17
PLACEMENT OF GLOWING EMBERS AND LAVA ROCK .......................................................... 18
OPERATION INSTRUCTIONS/FLAME APPEARANCE .............................................................. 18
VFSUR-(1,24,30) LIGHTING INSTRUCTIONS ............................................................................ 19
VFSUR WIRING ........................................................................................................................... 20
VFSUR TROUBLESHOOTING .................................................................................................... 21
VFSUE-(18,24,30) LIGHTING INSTRUCTIONS .......................................................................... 22
VFSUE WIRING ........................................................................................................................... 23
VFSUE REMOTE ELECTRONIC IGNITION AND CONTROL SYSTEM ................................24-27
VFSUE TROUBLESHOOTING .................................................................................................... 28
BURNER INSTRUCTIONS .......................................................................................................... 29
PILOT FLAME CHARACTERISTICS ........................................................................................... 30
CLEANING AND SERVICING ...................................................................................................... 31
VFSUR(18,24,30) PARTS LIST .................................................................................................... 32
VFSUR(18,24,30) PARTS VIEW .................................................................................................. 33
VFSUE(18,24,30) PARTS LIST .................................................................................................... 34
VFSUE(18,24,30) PARTS VIEW .................................................................................................. 35
MASTER PARTS DISTRIBUTOR LIST ........................................................................................ 36
HOW TO ORDER REPAIR PARTS .............................................................................................. 36
APPLIANCE SERVICE HISTORY ...........................................................................................37-38
WARRANTY TERMS .................................................................................................................... 39

TABLe OF cONTeNTS

Содержание VFSUE18-1









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды