Empire Comfort Systems VFSUE18-1 Скачать руководство пользователя страница 1

Страница: 1 / 40

INSTALLATION INSTrucTIONS

AND OwNer'S MANuAL

EMPIRE

Comfort Systems

VISTA SLOPE GLAZE MULTI-SIDED

Installer:

Leave this manual with the appliance.

consumer: retain this manual for future reference.

This appliance may be installed in an aftermarket

permanently located, manufactured (mobile) home,

where not prohibited by local codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases.

wArNING: If the information in these instructions

are not followed exactly, a fire or explosion may

result causing property damage, personal injury

or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— wHAT TO DO IF YOu SMeLL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas sup

plier.

uNVeNTeD GAS LOG HeATer Or

VeNTeD DecOrATIVe HeATer

MODeLS

VFSur(18,24,30)-3

VFSue(18,24,30)-1

This is an unvented gas-fired heater. It uses air (oxy

gen) from the room in which it is installed. Provisions

for adequate combustion and ventilation air must be

provided. refer to page 11.

wArNING: If not installed, operated and maintained

in accordance with the manufacturer's instructions,

this product could expose you to substances in fuel

or from fuel combustion which can cause death or

serious illness.

wATer VAPOr: A BY-PrODucT OF uNVeNTeD rOOM

HeATerS

water vapor is a by-product of gas combustion. An

unvented room heater produces approximately one (1)

ounce (30ml) of water for every 1,000 BTu's (.3Kw's)

of gas input per hour. refer to page 11.

Page 1

Содержание VFSUE18-1









































Результаты поиска

Содержание VFSUE18-1

Отзывы:

Бренды по названию

Популярные бренды

Empire Comfort Systems VFSUE18-1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание VFSUE18-1

Отзывы:

Бренды по названию

Популярные бренды